Simulation of Procast?

Zeinab Malekshahi Beiranvand @Zeinab-Malekshahi-Beiranvand

22 April 2020 0 2K Report

Hello,

Could I use Procast software for simulation of laser additive manufacturing?

Do you have any experience in this field?

Badges
Science topic

More Zeinab Malekshahi Beiranvand's questions See All

The measurement of cellular uptake of nanoparticles?

What protocol can be used to measure the cellular uptake of a nanoparticle? Is there a way to get more of a non-targeted nanoparticle into the cell? Why a fluorescent nanoparticle does not enter...

18 July 2024 7,153 2 View

What is the protocol for enzyme freeze drying?

what is the protocol for enzyme freeze drying?

09 July 2024 6,464 6 View

Can I use monthly precipitation for running the HEC-HMS model?

I don't have access to daily precipitation. Can I use monthly precipitation for running the HEC-HMS model? Let me know your expertise in Hec-HMS modeling. Thank you in advance for your kind help.

27 May 2024 1,495 1 View

How can add my published research on my profile page?

I really appreciate if anyone can help

14 May 2024 1,959 1 View

Constant Reciprocal of Step Size?

Hello I recently encountered a problem with the reciprocal of step size plot in Comsol Multiphysics. After a certain time (seconds) in a time-dependent solver, the plot oscillations will be...

04 May 2024 7,278 0 View

Why are the steppes not the same in Silvaco output?

In Silvaco, I have defined a semiconductor component. The electric field outputs have two problems. One is that the steps of X are not the same and they change, although I have defined a...

19 March 2024 4,649 0 View

How to comment on flowcytometric results?

Tissue culture and flowcytometry

16 March 2024 5,198 0 View

How can I use population balance model in COMSOL Multiphysics?

I need to apply the population balance model in Comsol software, for CFD simulation of a droplet distribution of dispersed phase in a liquid-liquid extraction column. I sincerely thank you for any...

31 January 2024 8,320 0 View

What the famous peronality trait theories/models?

The study of personality traits has been a prominent area in psychology, and various theories and models have been proposed to understand and categorize these traits. What are these theories?

04 January 2024 1,288 5 View

Have you heard about the nanozyme property of carbon nano onions?

Carbon Nanomaterials show enzyme-like characteristics (nanozymes), is there any research about nanozymes of carbon nano onions? Thanks

28 November 2023 8,227 2 View

How can I get the grain structure in Procast?

I would like someone to help me I am interested to know how the dendritic structure behaves inside the molds with the help of numerical methods

26 October 2021 4,798 1 View

Error when simulate casting process with Procast software?

I am trying to simulate the casting process of a part with the Procast software. I have the following problem. When I want to run, I run into an error as you see in the picture above. Does anyone...

20 January 2021 2,875 2 View

Error in simulation of ingot casting using procast?

I am trying to simulate the ingot casting process using Procast software. I have a problem. When I want to run, I would encounter with an error. the error is attached in this question. could you...

21 April 2020 8,358 2 View

Is it possible to couple fluid flow, heat transfer, phase change and mechanical stresses on the solidifying shell using COMSOL Multiphysics?

I am trying to simulate DC Casting of Aluminum Alloys in Comsol. I found an example related to Continuous Casting that it couples fluid flow, heat transfer and phase change during solidification...

28 March 2020 3,458 4 View

How can I simulate cyclic casting (LPDC) in the Procast with deference in each cycle time?

Procast cyclic parameters

01 February 2018 4,991 1 View

How can I simulate radiation of superalloy cast using ProCAST 2014 software?

When I trying to start simulation, it encounters an error and stop running and showing this message: " Unable to open input file *t.unf" How can I solve this problem??

06 July 2016 2,367 1 View

How can I simulate radiation of superalloy cast using ProCAST 2014 software?

When I trying to start simulation, it encounters an error and stop running and showing this message: " Unable to open input file *t.unf" How can I solve this problem??

06 July 2016 8,630 4 View

Could you please give me some user guide(tutorial) of procast software specially in diecast ?

I have been trying to model some part in procast but I can't. please help me and give me some user guide of this software, specially in diecast process. Thanks so much

03 April 2016 2,389 0 View

ProCast numerical simulation?

What is the best way to approach the casting simulation with the ProCast software? There is a lack of information about how to get started, even in the net! Anyone who knows more about it, please...

08 February 2016 8,526 4 View

How can I simulate heat and mass transfer in a continuous flow of a molten alloy into a copper reactor by Procast software?

See above

08 September 2014 7,586 2 View