How can I simulate radiation of superalloy cast using ProCAST 2014 software?

Mohammad Mostafaei @Mohammad_Mostafaei2

07 July 2016 1 2K Report

When I trying to start simulation, it encounters an error and stop running and showing this message:

" Unable to open input file *t.unf"

How can I solve this problem??

Reza Yarahmadi

Nothing, just buy and use the original one :).

Badges
Science topic

More Mohammad Mostafaei's questions See All

"Air entrapment" defect in magnesium sand casting

Can any one explain me the reason for "air entrapment" under steel chill in magnesium sand casting?

04 May 2017 4,781 1 View

How can I simulate radiation of superalloy cast using ProCAST 2014 software?

When I trying to start simulation, it encounters an error and stop running and showing this message: " Unable to open input file *t.unf" How can I solve this problem??

06 July 2016 8,630 4 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

AUX gas reading problem on QE with full MS and PRM method in one run?

Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...

06 August 2024 4,953 0 View

People weight in Oaxaca Blinder Decomposition on R?

Hello guys! Do you have experience running a Oaxaca-Blinder decomposition on R applying person weights. How do you suggest doing it? I have a variable PERWT which gives more information on how...

04 August 2024 6,033 0 View

Can anyone provide me with molecular docking softwares/ websites?

Molecular docking software/ websites?

02 August 2024 8,704 7 View

How to perform EEG source analysis on each trial of data separately?

Hello Everyone I have a question about structure for connectivity analysis on sources. My goal: preprocess and cut data into trials create headmodels, using template MRI file perform source...

30 July 2024 2,744 1 View

How to add Cr parameter in autodock?

When I run autogrid4 it says: autogrid4: ERROR: Unknown receptor type: "Cr" -- Add parameters for it to the parameter library first! Look forward to your reply.Thank you so much!

29 July 2024 488 0 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

I am working on my Master's thesis on the biogeography of the genus Ruagea and I would like to ask, could someone help me to check whether my result?

I created a file with my outgroup and ingroup species using Beauti, ran it in BEAST, viewed it in Tracer, and then used TreeAnnotator to create a file that I imported into RASP. Could someone...

28 July 2024 2,979 1 View

How do I run a dead well test for a QuantStudio 5 qPCR machine?

I am preparing to run a lot of samples on a 384 well plate and I wanted to test if any well in my PCR machine is dead so as not to lose any data. I would really appreciate help with how I can do...

24 July 2024 8,172 1 View