ProCast numerical simulation?

More Antonio Piccininni's questions See All

¿Are oxygen vacancies in semiconductors capable to change the band gap?

Dear all! Oxygen vacancies do raise negatively the Fermi level by increasing the negative charge in the semiconductor crystal structure. In the case of n-type semiconductors, I wonder if this...

30 July 2024 8,339 2 View

What is the solubility of Iron (+3) in Bismuth Oxide?

Dear all: I am modifying Bismuth Tungstate with Hematite (Fe2O3), so I would like to know about how much Iron(+3) can form a solid solution in a Bismuth Oxide matrix. Best wishes Marco

29 July 2024 2,163 1 View

How to express spinors with an arbitrary change of coordinates?

A spinor field in classical differential geometry is defined as a section of a spinor bundle, which is by definition the associated bundle constructed from the spinor representation and the...

14 May 2024 400 0 View

Would it be proper to mark species that do not migrate as "stationary" or "sedentary" ?

I am curious how should i label species in a certain swamp habitat, since i want to make a difference between the migratory and the "stationary" species. Both of the terms i mentioned in the title...

11 May 2024 3,216 5 View

Scotch tape Life Cycle Assessment or production environmental impacts?

Hi all, In the framework of a LCA of perovskite solar cells, I am looking for information about scotch tape, that is used to recover the metals deposited in some layers. Does anyone know of...

18 April 2024 1,678 0 View

Is there any relation between surface area and amorphization degree in high-energy ball-milled activated carbon? The main source could influence?

I milled two activated carbons, with different main sources (shell nutt and bituminous coal). The shell nut AC did not increase in surface area but had some degree of amorphization after milling....

17 April 2024 3,897 1 View

Culturing and mineralization protocol for MC3T3-E1 Sub 14 osteoblasts?

Recently, we have been encountering challenges in our laboratory in achieving satisfactory mineralization of MC3T3-E1 cell line. We would like to determine the optimal concentration of Ascorbic...

13 March 2024 7,500 1 View

¿Cómo puedo saber si una intervención con adolescentes problemáticos ha sido eficaz, o si por el contrario no ha sido adecuada?

Esta pregunta se refiere ha como podemos saber, si después de una intervención, ya sea en grupo o individualmente, a la hora de tratar con adolescentes problemáticos, nuestra intervención a sido...

11 March 2024 7,801 2 View

¿Cuáles son las principales acciones de respuesta del trabajo social, con respecto a menores en riesgo de exclusión social?

Esta pregunta hace referencia a las principales actuaciones, que un trabajador o una trabajadora social, debe de aplicar cuando se encuentra con un menor en riesgo de exclusión social, para que no...

11 March 2024 3,551 2 View

When and where was the term "Univalvia" used for Mollusca?

while attending class my professor asked us to count benthic species,and in my counting i mentioned sea snails,certain i have read multiple times that their classification is "univalvia" since...

27 February 2024 365 5 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out?

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out? For example consider a process for certain product manufacture where a new process flow...

31 July 2024 781 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

How to restart MD without using checkpint file in GROMACS?

Dear All Gromacs User I would like to restart MD without using checkpint .cpt files? I heard there is a way for acheiveing this. Any input and sugegstions are most welcome. Thanking You Budheswar

29 July 2024 3,084 8 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

A. V. Koltygin

I think these examples will help you. The truth in the latest versions ProCast embedded in a visual environment so the interface has changed considerably.

Antonio Piccininni

I'll try immediately the file you sent. Thanks a lot in advance.

Yaser Alaiwi

You can use ProCast to prepare the simulation boundary conditions and after solving the problem you can see the results using ESI Visual environment.

Dmitrii Chernikov

https://www.youtube.com/playlist?list=PL6VcYYMknPOWsF7PuTnh5rGuz-uW739Bz