Simulation in Fluent?

Mazhar Iqbal @Mazhar_Iqbal2

07 July 2013 1 4K Report

Can we use dimensionless formulation of the governing equations in Fluent?

Ahmad Fakheri

For incompressible flows you can, by assuming density to be one and setting viscosity to 1/Re.

Badges
Science topic

More Mazhar Iqbal's questions See All

What can be the possible application of fluid flow and heat transfer through a channel filled with a porous medium?

03 April 2014 5,165 7 View

Ignoring axial heat conduction?

Once modeling convective heat transfer problems through internal channels we normally ignore axial heat conduction. How valid is this assumption? I believe it has a relationship with the Pecelet...

11 December 2013 7,159 3 View

Is it possible to model hydro-dynamically fully developed channel flow in fluent.

In hydro-dynamically fully developed flow through duct one needs to calculate the solution (velocity profile) only at one cross section which remains invariant in the flow direction. Is it...

06 July 2013 4,460 20 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Why i can't get access to isosurface in fluent?

hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.

03 July 2024 5,418 4 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to converge PEMFC in Ansys Fluent?

I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...

26 June 2024 2,358 0 View

What is the exact mathematical formulae and the C++ code of EMMS drag model that is used and applied in ANSYS Fluent 2023?

EMMS - Energy Minimization Multi-Scale

18 June 2024 5,857 2 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View

Fluid flow through copper tube?

What does it mean meshed wall and shell conduction with or without run-out method use to meshing copper tube in Ansys fluent?

07 June 2024 9,030 3 View

How to address gradient discontinuities in CFD - Ansys Fluent?

Assuming I have three domains (three cubes e.g.) placed side by side, the electrical potential equation ( which I am specifying as a User Defined Scalar (UDS)) is solved in the left and right...

05 June 2024 4,153 0 View