Should the belt load be applied by using bearing load or remote force in ansys WB?

01 January 2015 1 2K Report

In ansys WB, for applying belt load, should it be applied by using bearing load or remote force?

I am trying to understand bearing load and remote force clearly.

For the case of belt load, you need to split the surface of the pulley according to angle of contact of the belt on pulley. Then apply the load using bearing load.

Bearing load considers the effect of load on a cylindrical surface, while remote force accounts the force which have an eccentric line of action.

Badges
Science topic

More D. M.'s questions See All

Why do I see yellow box and question mark while entering material data in ansys?

Hi I am trying to enter multi linear isotropic hardening data in a model. I see yellow mark for the first value as shown in snap. Why is this occurring?

07 August 2017 921 3 View

How do you generally perform weld analysis in ansys?

How the welds are modelled in ansys? and how do we interpret results? Anybody has example?? Please attach with answer.

04 May 2017 4,702 1 View

How to get actual deformation from modal analysis in ansys workbench?

How to get actual deformation from modal analysis in ansys workbench? Can we use participation factor and get actual deformation?

04 May 2017 7,274 1 View

Quick help needed with mid surface extraction in ansys workbench..?

Hi I am trying to extract mid surface of a component....I am getting something like the one in attached image... How to get rid of this issue...? Please help.

11 December 2016 3,639 4 View

Why a contact status shows both contat and target area inactive?

Hi Why a contact status shows both contat and target area inactive? See the attachment.

09 October 2016 9,432 0 View

Is it possible to have less nodes and more elements in ansys?

I have this model where the mesh statistics is like this:Nodes - 568678 elements - 1748934 Can this happen? What could be the reason for that?

09 October 2016 2,851 4 View

What does this error mean in ansys workbench?

Hi I am getting this error message: *** ERROR *** SUPPRESSED MESSAGE CP = 236.516 TIME= 19:33:53 The inversion subroutine was supplied with a singular matrix. *** ERROR...

09 October 2016 4,189 2 View

Cavitation analysis possible in CFD?

Hi Is cavitation analysis possible in CFD? If yes, can I find erosion rate in due to cavitation in CFD??

07 August 2016 5,966 0 View

How to decide if we can consider stress a certain location?

I am working on this bracket in ansys, I got stress plot as shown in picture attached. I am not sure if we can consider stress in red zone as true stress. The region is not in contact. I am...

06 July 2016 9,897 3 View

How the first value of convergence criteria is decided by ansys?

While performing non linear analysis, we come across force convergence, displacement convergence, etc. How is the first value of convergence criteria is decided by ansys software? How the...

04 May 2016 3,290 0 View

Do you think can be any diamond bearing rocks in Eastern part of Iran and western part of Afghanistan?

I want to know more about diamond ore deposits in world.

11 August 2024 2,167 1 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to increase simulation box size?

We intend to study the interaction between peptides and polymer (like PP, PE and PS) through MD simulations using Martini force fields ( Martini 2 for PP and Martini 3 for PE, PS). We have...

08 August 2024 4,842 0 View

Do you think can be any diamond bearing rocks in west of Iran?

I want to know more about diamond ore deposits in world.

07 August 2024 7,413 0 View

Research Methodology - Impact of Corporate Reputation on Stakeholders Behaviors?

Please can anyone support with the survey questions based on RQ measures and propose how to do it in FMCG industry and include as well the role of brand equity Thanks

06 August 2024 949 0 View

Anyone having idea about VN primer for miRNA primer design ?

How to design VN primer to attach with universal reverse primer

05 August 2024 2,116 3 View

Do you think can be any gas and oil bearing rocks in Eastern part of Iran?

I want to know more about petroleum deposits in Iran.

02 August 2024 8,725 3 View

Do you think can be any diamond bearing rocks in Eastern part of Iran near to Birjand city?

I want to know more about diamond ore deposits in Iran.

02 August 2024 7,399 0 View

Should I remove an item from a scale to raise Cronbach's alpha and McDonald's omega or is it better to leave it if they are both over .7 already?

Hello! I have this scale which had 10 items initially. I had to remove items 8 and 10 because they correlated negatively with the scale, and then I removed item 9 because Cronbach's alpha and...

01 August 2024 4,606 7 View