20 Questions 48 Answers 0 Followers
Questions related from D. M.
Hi I am trying to enter multi linear isotropic hardening data in a model. I see yellow mark for the first value as shown in snap. Why is this occurring?
08 August 2017 863 3 View
How the welds are modelled in ansys? and how do we interpret results? Anybody has example?? Please attach with answer.
05 May 2017 4,670 1 View
How to get actual deformation from modal analysis in ansys workbench? Can we use participation factor and get actual deformation?
05 May 2017 7,205 1 View
Hi I am trying to extract mid surface of a component....I am getting something like the one in attached image... How to get rid of this issue...? Please help.
12 December 2016 3,602 4 View
Hi I am getting this error message: *** ERROR *** SUPPRESSED MESSAGE CP = 236.516 TIME= 19:33:53 The inversion subroutine was supplied with a singular matrix. *** ERROR...
10 October 2016 4,001 2 View
I have this model where the mesh statistics is like this:Nodes - 568678 elements - 1748934 Can this happen? What could be the reason for that?
10 October 2016 2,811 4 View
Hi Why a contact status shows both contat and target area inactive? See the attachment.
10 October 2016 9,371 0 View
Hi Is cavitation analysis possible in CFD? If yes, can I find erosion rate in due to cavitation in CFD??
08 August 2016 5,933 0 View
I am working on this bracket in ansys, I got stress plot as shown in picture attached. I am not sure if we can consider stress in red zone as true stress. The region is not in contact. I am...
07 July 2016 9,854 3 View
While performing non linear analysis, we come across force convergence, displacement convergence, etc. How is the first value of convergence criteria is decided by ansys software? How the...
05 May 2016 3,257 0 View
Hi! I want to simulate a rough model for metal forming. The output should be the plate going down when displacement is applied. Please find the picture attached. I need to know what settings I...
04 April 2016 2,488 5 View
Hi. I want to use damping controls for a modal analysis. How to use this setting? As in how ansys works when these settings are applied? Please find the snaps attached for more details.
02 February 2016 9,013 6 View
Hi guys! I am working on this particular analysis, where I am using frictional contacts. While meshing I used hard behavior of mesh which allowed me to keep mesh size to minimum possible number....
01 January 2016 2,124 2 View
How can I simulate say steel bar in ansys workbench, where I want to draw stress strain diagram for it by taking values of stress at different forces applied? Basically, ansys should apply step by...
11 November 2015 4,741 1 View
hi I need to know if ductile iron brittleness is more or less than steel....
11 November 2015 709 1 View
I want to apply hub load (bearing load on a pulley). Normally I remove grooves and then apply hub load on the surface of pulley. ( I use ansys software) Is it possible to apply bearing load for...
09 September 2015 633 5 View
While solving modal analysis in ansys, there is a term wavefront, which can give you some idea if your runtime is less or more. Now when I was reading about wavefront I came across term...
06 June 2015 3,972 1 View
I really need help urgently this time. Can anybody tell me hw to find angles of a triangle when only two sides are known??? The triangle is not a right triangle....
03 March 2015 6,277 1 View
I need list of different elements in Ansys like for example solid 187, can be used where I need to capture bending or there surf 154 which can be used to apply internal pressure etc....
03 March 2015 3,593 2 View
In ansys WB, for applying belt load, should it be applied by using bearing load or remote force?I am trying to understand bearing load and remote force clearly.
01 January 2015 1,750 1 View