08 August 2018 1 4K Report

I have seen few sensors reported for measurement of dissolved nitrogen gas in soil, however is there any sensor reported to measure the dissolved nitrogen gas in blood/media may be in lab on chip platform?

More Afaque Manzoor Soomro's questions See All
Is there any way to cure the collagen for making thin membranes?

collagen is commercially available in liquid as well as in fibrils, is there any way through which we can cure and make a thin layer like membrane using collagen?

08 September 2018 1,025 3 View

What is effect of Laser wavelength selection in SPR sensor Performance?

I have gone through different papers on SPR design and SPR based biosensing; different papers report different wavelength value of laser however unable find any dicusion regarding why a particular...

08 September 2018 1,519 5 View

Is it possible to use SPR Sensor for Organ on Chip Platform?

I have gone through many papers regarding Surface Plasmon Resonance (SPR) sensors. I have not found its usage in Organ On Chip Platform. So Can we use this in such platform. any relevant reading...

03 April 2018 2,904 2 View

What is difference between Soft Sensor and Software sensor?

Is there any kind of technical difference between soft sensor and software sensor?

02 March 2018 9,468 2 View

Similar questions and discussions
Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View

What type of pressure sensor are usually used in microfluidics?

My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...

18 February 2021 9,928 2 View

Droplet PCR in plastic chips always result an unexpected band, any suggestion of possible contaminations and how to improve?

I am doing droplet based digital PCR inside plastic chips. I can get the correct band, but I also consistently get an unexpected band, slightly shorter. I attached a typical gel image here....

18 February 2021 6,618 2 View

How to realize refractive index values of 1 to 1.1?

Hello researchers! While studying the literature on refractive index sensors, most of the articles simulate their devices with a refractive index ranging from 1 to 1.1, with small steps in...

17 February 2021 1,578 4 View

What should a smart water system look like?

Our team is designing a smart water C&C dashboard for a smart city initiative. As we look into the current smart water system landscape, we couldn't reconcile to a definitive solution that...

16 February 2021 1,094 3 View

Receiving very less number of hits and events in acoustic emission tests?

I am doing a three point bend test with concrete specimen of dimension 280mm*90mm*90mm. I am putting 2 sensors near the notch with 3cms away from both the sides. the experiment ran for 20 mins but...

13 February 2021 2,990 1 View

How to increase coupling range (distance between reader and sensor coils) in LC resonance circuit?

Hello great researchers, I am working on a wireless pressure monitoring project where sensing part is actually an LC resonance sensor and I am using a planar coil as a reader to get wireless...

11 February 2021 4,148 5 View

I am looking for a microbend optical sensor design...can anyone please provide me some idea about it??

I am working on a landslide model...i need an optical sensor to determine the amount of pore pressure and other values..i am thinking of using a microbend sensor. Can anyone please provide me with...

11 February 2021 5,911 2 View

How to eliminate noise when using a sensor with instrumentation amplifier and giving it's output to Arduino?

When I am trying to implement a pressure sensor through instrumentation amplifier and then giving it's output to Arduino, I am getting garbage value due to noise, so how to eliminate it.

05 February 2021 8,598 11 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close