How much the microbial exploration in oil and gas industry is applicable?

Microbial oil and gas prospecting (MPOG) I would grateful it if you could provide me with your invaluable comments and ideas on the following questions: 1- Do you consider MPOG as a promising...

15 December 2020 9,895 2 View

How can I apply heat flux on edge of a layered shell in Comsol?

Hi everybody I modeled a piece of CFRP in Comsol with a thickness of about 2cm, I used the new module in Comsol 5.5 ( thermal stress in layered shells) Everything has gone well but after the...

10 May 2020 8,246 3 View

How to get permission for any content reproduced in a new submission?

I have been asked to get the required permission for the figures reproduced in my review paper from other publications. All the figures which are reproduced from other publications appropriately...

13 February 2020 4,970 8 View

How are silver nanowires dispersed to isopropanol?

I synthesised nano wires using Polyol method then centrifuged and I have dispersed them into ethanol But they did not disperse into isopropanol. How do I disperse them into isopropanol (IPA)?

23 July 2019 4,428 1 View

FMRI between-group correlation study: how to specify study variables?

I am designing an fMRI study for my dissertion and I got consfused as I got to this part. Since, I have to signify the study variables one by one in a chart and provide theoritical and operational...

20 January 2019 7,607 9 View

Do you think that exist relation between desertification and climate change?

Today, desertification is one of major environmental problems.

08 October 2017 9,600 12 View

How can i define a reference point in ABAQUS?

02 December 2016 5,381 10 View

What is the best method of intering different temperature conditions into different areas of a unit solid volume?

21 July 2016 7,328 1 View

Is producing boiling water with low quantity from a fluid with a lower temperature but vast quantity theoretically impossible?

I am an electrical engineer and I am not much familiar with fluid mechanics, I am curious to know that Is producing boiling water with low quantity from a fluid with a lower temperature but vast...

28 June 2016 3,487 6 View

Whats the real behavior of rc circuits?

In series RC circuit with dc power supply the maximum capacitor voltage should be equal to power supply but in my experiments it's less than expected value and it's proportional to resistor, while...

14 December 2014 4,350 64 View

Tooth extraction and subsequent dental implant placement in Sprague-Dawley rats induce differential changes in anterior digastric myofibre size and ?

01 March 2021 7,254 3 View

How to identify what type of fillers are in a polymer?

Hello everyone, I have some PHAs blended with fillers and nucleating agents, yet I don't know what kind of fillers or nucleating agents. The producer has shut down and there's no way to get in...

24 February 2021 1,356 8 View

How the Ground Plane implantation is performed without damaging (and w/o varying the undoped nature) the top Si (8-10 nm) in FDSOI technology ?

It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...

24 February 2021 5,974 4 View

How does elongation affect the resistance of an electrode?

What are the testing rate for electrodes recommended by ASTM for cochlear implants. I am currently doing the 15mm/min elongatio testing.

22 February 2021 1,515 1 View

Should the AUC in a concentration-time graph of a subcutaneous implant be roughly the same for poeple?

I have 2 concentration time curves of a subcut drug implant. the first group has a peak around the 50 day mark where as the second group does not. Both groups received the same implant by the same...

10 February 2021 2,305 3 View

Looking for help in writing my research proposal ?

Looking for help in writing my research proposal in the following areas : HRIS / HR / Change management / Remote work Please get in touch with me if that sounds like your expertise. Thank you very...

08 February 2021 5,434 4 View

Can I polymerize NIPPAm with PEGmethacrylate or only with PEGacrylate?

I want to perform the synthesis of a hydrogel and I want to know if I can polymerize NIPPAm with PEGmethacrylate or only with PEGacrylate?

02 February 2021 2,106 6 View

How can solve/disperse silicon nanoparticles in water?

I want to add silicon nanoparticles to my hydrogel, but when I sonicated these particles with water to disperse them in water, they agglomerated on the water's surface. How can I disperse them in...

26 January 2021 213 4 View

Anyone know how to dilute strong hydrogel structure?

I am working on PVA-GMA hydrogel that is a really strong polymeric structure like rubber. Because I am in the middle of analysis, it is difficult to dissolve the gel using a common solvent. I...

20 January 2021 3,501 2 View

How can I stain 3d printed cells in hydrogel without damaging the gel?

I tried staining my cells in a gel using standard protocols with 4PF% for fixation and triton-X or saponin for permeabilization but the gel always gets damaged throughout the steps, and at the end...

17 January 2021 4,170 1 View