Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

Do anyone here can help us in the field of molecular docking?

We have synthesized various metal complexes with different environment around the metals. Now to see the application of synthesized complexes we need this study also. we are also interested in...

01 March 2021 1,899 2 View

Analysis of CRD two factor using R studio ?

Hello everyone. I have conducted the research on post harvest longevity of tomato crop using plastic packaging and different doses of chemicals as two different factors. The design of experiment I...

28 February 2021 8,189 3 View

What is the exact mechanism of the antimicrobial effect of local anesthetics?

The antimicrobial effect of local anesthetics has been known for more than 50 years, but it still seems to have an unclear mechanism of action. which bacteria? which concentration? etc etc. ....

27 February 2021 4,450 2 View

How can I selectively dry etch Ti on a polymer substrate?

24 February 2021 5,378 1 View

Resistivity of PVD TiNx thin films vs. N2 flow?

In the PVD of TiN thin films (~100A), I've found the resistivity of the TiN films dropped from ~100 to 60um*cm with N2 flow increasing up to the metallic mode ending point; then the resistivity...

21 February 2021 1,864 2 View

What are your alternative data collection methods during the pandemic? What are the pros and cons?

Dear colleagues We are exploring possible data collection methods for environment and behavior research in the context of architectural environments. Have you conducted any Post Occupancy...

16 February 2021 2,575 4 View

Can bio-decomposer be a successful alternative to reduce residue burning?

To maintain the proper crop plan most of the times there is not enough time to make the field ready for the next crop. In this particular context , can bio-decompser be a solution? What about...

16 February 2021 7,068 24 View

Is there any effective FEM solver to perform simulation of balloon inflation with large deformation (e.g. 300% strain)?

Hi! Thank you for your time, attention, and support. I am currently using FEM solver Abaqus to perform a set of balloon inflation simulations, trying to understand the deformation shape, stress,...

14 February 2021 2,524 4 View

What is Flat Lens Antenna?

28 February 2021 5,433 3 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

EMSA troubleshooting. Protein-DNA complex not migrating, cold probe lane with multiple bands. Can anyone help?

I'm running an EMSA to show the DNA binding activity of recombinant proteins versus the Wild type. Previous assays run by my research group using a different test system show the protein-DNA...

24 February 2021 8,325 1 View

Helix antenna coupling problem?

Dealing with a helix antenna, made with flexible material and not rigid like using a PCB board or wire. At the beginning of the helix is too close to the ground plane, causing coupling. How can I...

21 February 2021 4,453 3 View

How to combine two geometries in LAMMPS ?

I am trying to simulate contact angle of water on a quartz slab using LAMMPS. I have created and equilibriated the quartz slab and the water cluster separately. Now I want to create a composite...

17 February 2021 5,884 2 View

Which method need to be used to predict crack propagation?

Need to predict the crack propagation phenomenon in a CI component. Suggestions are needed regarding the the methods ( XFEM, J integral, etc.,) which will predict the crack propagation behavior...

06 February 2021 1,936 4 View

How to mesh complex geometry?

I have been trying to mesh some complex geometry and have been having issues. I have attached images of the geometry in question. This structure is very large in size but has some comparatively...

05 February 2021 6,379 5 View

Please recommend me the proper steps (blocking method) to generate Hexahedral mesh of the following geometry inside ICEM-CFD?

I am facing an issue while blocking for the geometry mentioned in the image. After blocking it ends with a triangular block due to its shape. How to create a hexahedral mesh for this geometry in...

02 February 2021 888 1 View

How to prepare protein samples in EMSA assay?

Recently l was studying EMSA assay, but l didn't find any detailed information about protein sample. we can use two kinds of protein, including crude protein extracts and recombinant proteins. but...

02 February 2021 10,047 3 View