Who has analyzed essential oils in hemp and/or hops on HPLC?

I am trying to utilize my equipment as efficient as possible and want to try to run terpenenes (essential oils) on hemp and hops. Has anyone tried this before or does anyone know whom to contact...

17 August 2020 7,267 6 View

Where can I find academic books on sustainability and also graded/extended reading?

I am purchasing books from my designated budget. Academic books on either sustainability, UNESCO 2030 goals, and also graded and extended reading. Any suggestions would be very helpful and...

09 March 2020 4,723 5 View

Can a cross-over design control for regression toward the mean?

04 March 2020 3,302 3 View

Importance of light chain type on isotype control antibodies for flow cytometry?

I am putting together a panel for flow cytometry, for one particular antibody the only available isotype control has a different light chain to the test antibody. My test antibody is BV711-CD25...

10 June 2019 3,466 2 View

Can anyone explain how I choose a surfactant for a water in oil macroemulsion, and how I decide what volumes of each substance to use?

I am trying to create a water in oil macroemulsion with droplet sizes as large as possible (hoping to get between 0.1-1mm). I have no idea what surfactant to use or the volume of each phase to...

31 May 2019 7,376 3 View

I am planning to do a project management study that is related to health. What is the best topic to research on?

Any suggestions i will appreciate

06 April 2019 7,158 8 View

Optimising RT-qPCR for the detection of very low abundace IL-17A transcripts from human PBMC mRNA?

I am performing qPCR to quantify cytokine expression in human peripheral blood mononuclear cells. I have found it very difficult to get consistent results when assaying for IL-17A. Currently I am...

23 January 2019 8,404 1 View

Can DNase treatments to RNA preparations cause damage or loss to the mRNA?

When performing qPCR, I have noticed that cDNA made from RNA preparations treated with Turbo DNase (Invitrogen) prior to reverse transcription produce CT values that are shifted several cycles...

31 October 2018 9,688 5 View

Deaf friends in Dar es Salaam have asked: What research has been done on the signed language(s) used in Moshi and Arusha, Tanzania?

My Deaf friends in Dar es Salaam, Tanzania have told me the the sign language used in Moshi and Arusha is different than the signed languages used in other parts of Tanzania. They asked me to...

11 July 2018 3,549 1 View

Is a cell self-conscious?

10 September 2017 5,686 88 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View