Pressuremeter curve on 2D flac

More Franck William's questions See All

How to convert a privately loaded document into a public document?

I attempted to make a privately uploaded text public but a window appeared that said an error occurred. There was no explanation provided as to why there was an error or what might be done to...

05 August 2024 8,025 7 View

How closely does an elastic sheet conform to what's below it?

See the attached file for an illustration of this problem. Consider an elastic sheet S (orange) that’s laying atop a solid base B (blue). The sheet is under tension (arrows) and is held to the...

30 June 2024 747 4 View

Studies comparing Collaborative vs. Conventional environmental management?

I am working on a literature review of studies that systematically compare at least one case of collaborative governance to one or more cases of conventional governance (or that compare multiple...

25 June 2024 5,151 2 View

I am trying to find a recent report out of Canada about the underestimation of cardiovascular risk by the Pooled Cohort Equations. Help?

I am trying to find the recent reference from the recent Canadian report that showed that the Pooled Cohort Equations severely underestimated cardiovascular risk. I appreciate any help you can give.

04 June 2024 8,599 3 View

WHen using ICA with only 6 or 8 EEG Channels is there an algorithm for which channels to remove?

I have a system that has only 6 EEG channels recorded. When I run the ICA it reports back that I have 5 independent channels. Is there an algorithm for selecting the best combination of channels...

29 May 2024 4,793 3 View

How to import xyz boundary in Mike Zero ?

Good Morning, I'm trying to import xyz file following tutorials but I have an error message (in the figure below). I need help

29 May 2024 1,360 2 View

How to calculate the abscissa and ordinate for the interpersonal circumplex ?

Hello I'd like a little clarification on how to calculate the abscissa and ordinate for the Interpersonal Circumplex. After ipsatising each score for octants, I use Wiggins' (1995) formula to...

21 May 2024 6,876 0 View

Help, I am new & confused.?

I understanding that a book I co-wrote and edited may be available on your platform. I searched and cannot find it. The title: Compnent-Based Software Engineering: Putting the Pieces Together....

21 May 2024 8,622 0 View

Is Anser Press predatory? I got a request to review a paper for "Economic Analysis Letters"-is this a legit journal?

I am just trying to find out if Anser Press is legit-there is a journal "Economic Analysis Letters" that wants me to referee for them.

18 May 2024 5,886 2 View

What are the aims and objectives of food security and sustainable farming?

I am writing a project proposal on food security and sustainable farming in solomon islands context

11 May 2024 3,891 3 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

How do we get the plasticity multiplier of M-C criterion in FLAC 3D?

In the Itasca FLAC3D Documentation, it provides the expression of plasticity multiplier regarding Mohr-Coulomb criterion directly, without a detailed derivation process. Could anyone share the...

12 July 2024 7,850 0 View

The HCP removal rate is lower than usual in concentration step, why?

Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...

11 July 2024 5,380 0 View

Pressure in Iron Iron Carbide?

What will be the pressure in Iron Iron-Carbide diagram? It is at atmospheric pressure?

05 July 2024 1,891 0 View

How to Perform Randall-Selitto Test (Paw Pressure Test) In Mice?

Hi All, My name is Sumaiya, a PhD student at the University of Queensland. I am looking for some suggestions on how to hold mice and perform Randall-Selitto Test by using Paw Pressure Randall...

30 June 2024 6,004 0 View

How do I dedicate my entire life in doing only one thing?

I would like to dedicate my entire life in doing only one activity alone and nothing else. How do I achieve it in this world full of unavoidable distractions and societal pressures?

24 June 2024 298 1 View