Excellent industrial application from recycle the waste steel slag and sludge materials. abrasive tools and cutting tools, if possible as composite materials
Article Energy effective approach for activation of metallurgical slag
Thank you
some of these materials are used in the concrete as cement replacement
New composite materials from silk and epoxy material
15 December 2021 3,065 13 View
I had finished docking with MOE molecular operating environment, However, I was faced with docking result, what this result and how to find the affinity, binding and number, and type of binding?
05 November 2021 9,952 4 View
Always there is a yield gap take places between conventional and organic farming systems. Past literatures indicated that the main cause of appearing yield gap is due to the transformation of...
16 June 2021 2,935 18 View
Need to make new brake pads in industrial applications as composite materials from waste steel materials slag and sludge.
07 May 2021 3,227 6 View
ما رأيك في ايجابيات وسلبيات البقاء في المنزل خلال وباء كورونا؟
10 June 2020 7,603 22 View
I need to predict fatigue analysis by using FEA.
07 February 2020 7,844 4 View
To know the difference between protein and peptide
26 December 2019 9,668 3 View
proteins and peptides
08 April 2018 2,306 8 View
How will one know e-health excellence?
28 November 2013 7,180 2 View
I have simple research published on androgen receptors and the difference between normal and mutated receptors this is my article https://f1000research.com/articles/11-516/v1 please help with...
01 January 1970 4,976 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?
25 July 2024 9,408 0 View
I am looking for a lipid waste disposal method, keeping in mind the environmental, health and safety aspect of lipid waste. Could someone please provide guidelines or the lowest acceptable...
25 July 2024 637 5 View
I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...
24 July 2024 4,393 2 View