Polymers are having solubilising property in organic solvents ?

More Pilli Govindaiah's questions See All

How can I calculate the unit of enzymes with oxygraph results?

Hi, I did enzyme substrate reaction by using oxygraphy instrument. I have the crude enzyme concentration and the rate of the reaction, is it possible to calculate enzyme units and activity of the...

27 February 2023 9,951 4 View

Feedback required on possible research subject: How can M&A activity impact growth and innovation in the disruption prone Finance Technology industry?

Hi all, I'm hoping to elicit some feedback from this forum on a piece of research I'm about to undertake. My subject is related to mergers & acquisitions in the finance technology industry,...

27 July 2020 7,351 3 View

From where the first seed crystal of Silicon is obtained for Czochralski or Float zone technique of Si crystal growth?

Czochralski and float zone methods are used to grow the single crystalline silicon which uses a single crystalline silicon seed.... How the seed is obtained or grown?

13 September 2019 5,374 3 View

How to realise the fm modulation and demodulation on 70MHz carrier digitally on FPGA and what are the required ADC and DAC required?

Any suggestion and/or reference is welcomed...

29 November 2018 2,879 5 View

What is the gas(bubbles) that is produced when KOH is dissolved in water?

When I dissolve KOH pellets in water I observe bubbles coming from the solution. Is it H2 or water vapor?

29 January 2017 1,571 7 View

Can we use settlement measurement chart based on SPT (fig9 8009,PART 1) for pile settlement?

change in stress is very much less when compared to initial stress in case of piles. so settlement is generally less.But with using the chart i am getting more settlements as that chart does not...

07 November 2016 5,112 3 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

What is the solvent for 8YSZ nano material?

I need to do some experiment with it in liquid form.

07 August 2024 613 3 View

Which solvent is better to dissolve with secondary metabolites extracted from fungi?

I work on MCF7 cell cell for anticaner purpose and I wa to do drug preperation the drug ( secondary metabolites extracted from Aspergillus) My question which solvent is better with these secodary...

03 August 2024 4,725 2 View

I need to dissolve stigmasterol for an animal experiment, it hasn't dissolved in either DMSO or vegetable oil. Can anyone recommend the best solvent?

Hello everyone, I need to dissolve stigmasterol for an animal experiment, but it hasn't dissolved in either DMSO or vegetable oil. Can anyone recommend the best solvent for stigmasterol?

01 August 2024 7,504 2 View

Inquiry on Maximum Nucleic Acid Volume for 2.5 mL Liposome Solution?

I am currently working on a project involving liposomes and need to determine the maximum volume of siRNA that can be added to a 2.5 mL liposome solution with a total lipid concentration of 10...

30 July 2024 6,420 1 View

How can I use DFT-D3 correction ( Siesta version 5.0.1)?

Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...

27 July 2024 5,748 0 View

EDC carbodiimide and NHS easter 's half life among different pH?

It has been long known that EDC carbodiimide and NHS easter's half life agains hydrolysis are highly related to pH. However, very surprisingly, not yet found a paper giving a table/chart of their...

25 July 2024 8,738 0 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

Why methanol and sulphuric acid used in the analysis of polyhydroxyalkanoates (PHA) by GC-MS?

Why methanol and sulphuric acid, used in the analysis of polyhydroxyalkanoates (PHA) methyl esters by GC-MS? Additionally, why do we typically use non-polar solvents in GC-MS?

22 July 2024 1,210 2 View

How to eliminate the carry-over effect in GC-MS/MS system?

Hi, I am a PhD student working at Jagiellonian University, Faculty of Chemistry. My work is related to the development of new analytical methods for the quantification of short-chain fatty acids...

22 July 2024 5,492 6 View

Alain Celzard

If your polymer is thermoset, i.e., is a resin, then it is normal that it is insoluble in any solvent. Only non-crosslinked polymers at thermoplastics can be easily solubilised, not thermoset (like epoxy, phenol-formol, etc.)

What is the chemical nature of your polymer, and how was it prepared ?

Alain

Bhausaheb B. Sole

what is nature of your synthesized polymer so i can help you.