26 January 2020 3 3K Report

Can anyone suggest good journal papers dealing with CFD of plastic pyrolysis using ANSYS or any other software?

More Gopikrishnan Kailas's questions See All
What height the instrument should be placed for measurement of ambient air quality and different gases as well as fetch area in agriculture?

What height the instrument should be placed for measurement of ambient air quality and different gases as well as fetch area in agriculture?

10 October 2021 9,931 3 View

If we increase the number of holes in the distributor plate will the minimum fluidization velocity decrease ?

We are trying to fluidize sand of diameter 300 to 600 microns using a fluidized bed of diameter 65mm. The bed is fluidizing at 0.7 meters per second. According to the literature, the bed must...

01 January 2021 474 8 View

How to calculate the flow rate required for fluidization for a fluidized bed gasifier ?

We need to calculate the flow rate of air required for fluidization of the bed. We have a compressor which gives air at 7 bar and a 1 bar rotameter for measuring the flow rate in LPM. How can I...

16 December 2020 2,478 3 View

Why does diesel have sulphur content in it?

What sulphur compounds are present in diesel fuel

10 December 2020 9,916 3 View

How to calculate the required flow rate of inert gas during a pyrolysis reaction?

For continuous pyrolysis reaction, we need a continuous flow of nitrogen to remove the evolved pyrolysis vapours and condense them simultaneously. How can we calculate the required flow rate? Is...

06 December 2020 4,387 6 View

How to add elemental carbon in DWSIM?

How can we add carbon element in dwsim?

22 July 2020 2,667 4 View

Why plastic pyrolysis oil is used in Diesel or CI engines and not in SI or petrol engines?

Why most of the research in the literature focuses more on the application of plastic pyrolysis oil in CI engines and not on the SI engine? Does it have to do with the composition of the oil? If...

21 July 2020 3,152 0 View

How can we add LDPE as a new compound using compound creator in DWSIM?

I am only able to add polyethylene which is not the exact properties of LDPE. The molecular weight and other properties don't match the literature. If I have to add the properties, then what list...

20 July 2020 1,423 1 View

What is the latest research going on in the area of plastic pyrolysis?

What are the latest developments taking place in the field of plastic pyrolysis? Any new breakthroughs that can improve the process? Any new areas that everyone should explore so as to do...

25 January 2020 7,247 5 View

Which is the best International conference for pyrolysis?

Which is the best International conference to attend in the area of pyrolysis? (where we can meet top researchers in the field)

10 December 2019 1,441 5 View

Similar questions and discussions
Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to generate a citation of my paper from ResearchGate?

How we can cite the papers from ResearchGate. I am trying to create citations for this article, Quantum Machine Learning Algorithms for Optimization Problems: Theory, Implementation, and...

08 August 2024 6,690 3 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Aspen Plus Simulation?

Greetings When one is to perform Simulation or modelling of Pyrolysis of Biomass Waste materials using Aspen Plus software, and one has both the macromolecules breakdown (Cellulose, Lignin and...

06 August 2024 5,023 1 View

How to get links for copyrights for papers?

how to get links for copyrights for papers?

06 August 2024 7,410 1 View

How to determine positive-stained cells in FACS? Use isotype or unstained control?

To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...

06 August 2024 6,728 6 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close