Please I need the chemkin file for biodiesel C10H22(n-decane) in ANSYS FLUENT?

21 July 2018 1 2K Report

My research is on direct injection biodiesel fueled diesel engine using numerical simulation. The software I am using is ANSYS FLUENT and I want the biodiesel chemkin reaction mechanism to help me run my simulation case.

Mohsin Khan

search it on Lawrence livermore national laboratory website

Badges
Science topic

More Peter Otchere's questions See All

I have a time series data of some biochemical studies ( DNA and Chromosomal damage) which I intend to use to further predict into future ?

I have a time series data of some biochemical studies ( DNA and Chromosomal damage) which I intend to use to further predict into future without necessarily conducting the assay for an extended...

23 February 2021 7,842 1 View

No mRNA increase in PCR after successful transfection in ARPE-19 cells ?

Hello, i am a bit curious about my results. I transfected the human cell Line ARPE-19 with a Plasmid containing a GFP tagged p53 (p53-GFP, Plasmid #11770). After 24h i checked under the...

18 February 2021 3,811 7 View

Do there exist stand-alone permanently in-ground soil-moisture sensors with an installed GSM module, for outdoor use?

Am searching for a stand-alone permanently in-ground soil-moisture sensor with an installed GSM module, for outdoor use. The idea is for the sensor to send a moisture reading via a cellphone text...

04 February 2021 2,047 4 View

What is the easiest way to remove the water from organic solvents?

Hello everyone! I have one question. I have couple of solvents and all of them were pure when they were bought but after some months or years of storage after opening I am not 100% sure about...

03 February 2021 2,154 8 View

Virus neutralization assay in BSL2 lab?

Hi I want to set up a virus neutralisation assay such as PRNT or FRNT at my lab (BSL2), but im uncertain of the bio safety requirements that has to be fulfilled in order to work with...

01 February 2021 5,626 3 View

Using LINK11 to Apply force in ANSYS APDL?

I'm trying to use LINK11 to apply a force as if it was a cable pulling a structure twowards a point in ANSYS APDL. When I solve the model, the deformation of the overall structure is far too...

30 January 2021 7,919 1 View

Cytoflex Flowcytometer, clotting issues and cleaning procedures?

We have been having clotting issues with our Cytoflex S from Beckman Coulter. Back in December 2020, we had to have the tubing system and sample needles replaced, but we are beginning to observe...

28 January 2021 6,897 2 View

Difficulties purifying Outer Membrane Vesicles using a Sucrose Density Gradient: Unable to detect any protein after this process?

I'm currently trying to purify Outer Membrane Vesicles (OMVs) following their extraction from the bacteria I'm working with. After the initial extraction the concentration of protein seems good...

27 January 2021 6,852 3 View

What excamples do you know wasting unused contents of "empty" packaged products?

Most of us use tooth paste more times a day. The empty tube we throw away. I wondered how empty the tube really is. This does not sound being Research? I began to collect empty tubes...

19 January 2021 808 3 View

What is the largest disadvantage in using of face masks at present? What would you like to be improved?

We all use face masks many hours a day. I wonder what are your items you like to be improved. We have the opportunity to write an application for support to a sponsor. Your answers will help us a...

18 January 2021 1,311 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How do I increase the yield of my PCR product?

Hello, We would like to increase the yield of our PCR product. We are running a series of PCR reactions that is targeting ~1.1kb sequence. We begin each reaction with ~400pg of template DNA...

02 March 2021 4,029 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

PACYC PCR not working after several attempts. Would anyone have any suggestions?

So, I have been trying to run a pACYC PCR which will be used later on for a Gibson Assembly. However the PCR is not working. I have already tried gradient PCR and changing extension time; however...

02 March 2021 1,146 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to address this issue in the analysis of Real-Time PCR results?

To dear Researchers, I was analyzing a series of concentration for estimation of Real-Time PCR efficiency. The concentration was 1:10. I used MS-excel to evaluate Slope. The result of slope was -8...

01 March 2021 8,683 4 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View