Monolayer of MoTe2 using mechanical Exfoliation?

Hello dear researchers, has anyone experience in obtaining the monolayer of material MoTe2 successfully by the mechanical exfoliation method ?? I have tried a lot of times, but the best thinner...

08 September 2018 7,432 3 View

Polarization modulation adds information to the Super resolution?

Hello dear researchers, Is that true, due to the modulation, we can map the weak signals and alone with modulation, we can get super-resolution??? If we can get the weak signals by using...

08 September 2017 3,080 0 View

Is that possible to retrieve the near field signal by inverse scattering calculation in the far field region???

Hello dear researchers, Scanning near field microscopy is a standard method for mapping the near field localized amplitude and phase. Is that possible, by inverse calculation( Inversely fit the...

07 August 2017 440 17 View

Multipolar response from dimmer and trimer nanosphere??

Hello dear all researchers, as we all know for the single sphere (Monomer) we have Mie solution of the Maxwells equations. By using Mie theory, we can easily calculate the multipolar effects...

07 August 2017 6,201 10 View

Near Field and Far field Imaging with same simulation area??

I have already used COMSOL, FDTD, and CST software, But they do not offer to map the near and far field distribution at the same simulation area around the particle. Is there any way to simulate...

07 August 2017 4,257 3 View

Measuring scattering cross-section without a Spectrometer?

Hello, dear researchers, I want to ask that I am using the system as shown in figure 2. I performed an experiment and I measured total reflected intensity from the CCD as shown in figure 1(a). I...

09 October 2016 702 7 View

Effect of heat on nano-particle scattering?

hello dear all, i have performed some NF measurement on nanoparticles whose size range in the 500nm to 1500 nm with wavelength of 532 nm. The system is like polarization microscopy. i have heated...

05 June 2016 7,750 4 View

How can I buy the chiral shape nanoparticles in China?

Hello Dear researchers, especially from China, I want to study the NF and FF scattering from Chiral shape nanoparticle of the size ranges from 700 nm to 1200 nm, From where i can buy in a cheap...

05 June 2016 4,148 4 View

Effect of annealing on electromagnetic scattering?

Hello dear researchers, I have Tio2 nanowires, what will be possible effects on scattering spectra if we anneal them at 700C and 800C. Thanks

04 May 2016 1,720 6 View

Polarization Modulation breaking the diffraction Limit?

Hello Guys i want to know that what are the possible ways that we can image the object beyond the diffraction limit using polarization Modulation?

04 May 2016 4,254 5 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View