NFC antenna coil design help in ansys ? and mehtod to calcualte the read range ? which is better using SBR+ solver?

29 September 2025 0 2K Report

currently i m working on antenna coil design for the nfc enabled atm card , mainly metal card , using ST topaz chip ?

any one guide me or send some insights to design in hfss, when i try to design in hfss, how to get the perfect pitch using poly line and the excitation port how to give it ?

Badges
Science topic

More Venkata Lochan Reddy's questions See All

What precautions should be taken while handling S. aureus enterotoxin Type B in the lab?

I would like to understand potential safety concerns while handling SEB in the lab. Especially while working in animal house facility. Would like to know precautions for handling. Sigma MSDS...

07 August 2024 6,034 3 View

Tissue homogenization in mouse with FastPrep-24™ 5G - is the D matrix system useful?

I need to lyse and homogenise mouse tissues. So far I have experimented with liver and lung tissue, using matrix D. The liver was completely lysed with 6 repetitions of the standard program, but...

31 July 2024 9,186 0 View

Can any one let me know the PDE value for Tert-Butylamine in order to control in the API?

PDE value for Tert-Butylamine

24 July 2024 1,166 0 View

Cloning restrction digestion needed before sequencing?

Hello, recently i am an issue swith cloning where I am using the subclone method to insert my gene length is 1.5kb and my vector(pMAL-c6T) is 5kb I got the colonies which i screened through the...

04 July 2024 7,977 2 View

How can we reduce the porosity of tungsten oxide (WO3) thin films during DC sputtering deposition (target: W, power: 100 W, 75 W, and 50 W)?

We are fabricating a tandem structure where a ~50 nm thick WO3 film is deposited between two metal films using DC sputtering. We use a mixture of Ar and O2 gases at different flow rates while...

01 July 2024 2,686 2 View

Haplotype analysis software or R code?

Is there any user-friendly software or R code for haplotype analysis? I run GWAS analysis and now plan to run haplotype analysis. Any suggestions, please?

23 June 2024 4,911 2 View

How does a Man-in-the-Middle (MitM) attack work in the context of Transport Layer Security (TLS), and what specific mechanisms can be employed ?

Context In the realm of cybersecurity, Transport Layer Security (TLS) is widely used to secure communications over a computer network. Despite its robust encryption mechanisms, TLS is still...

19 June 2024 6,595 3 View

Does the first semicircle represent contact resistance, and what is the reason for its generation?

My research topic is the corrosion of gray cast iron in methanol. EIS measurements were conducted at open circuit potentials (Eoc) using a sinusoidal signal with the amplitude of 10 mV from 100...

05 June 2024 6,891 2 View

How to perform static structural analysis in ansys to calculate Gear body & Gear tooth deformation due to rotational speed?

I would like to calculate the gear wheel and gear tooth deformation due to rotational speed? The gear shaft is mounted on hydrodynamic bearings. What are the boundary conditions need to apply?...

21 May 2024 8,067 0 View

Why We Can Not See God ?

Dear In the UNIVERSE from a sand grain to Sun including man, all are bodies of different sizes. Every body has a SHAPE//FORM A body with a shape gets a NAME Every body has a LIMIT And every body...

18 May 2024 3,012 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

How to find ECC from radiation pattern on cst ?

i need to find ECC for 4-MIMO antenna using radiation pattern on CST

16 July 2024 7,291 1 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

What should I upgrade in my computer to speed up simulation in CST?

I want to reduce simulation time in CST for frequency domain solver by upgrading my computer. I already have discrete GPU but it doesn't seem to make any difference at all compared to integreted...

10 July 2024 2,789 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to know the TM/TE modes in antenna design in CST studio?

How to know the TM/TE modes in antenna design in CST studio? Example: TM01 ,TM02 ,TM10, TM12, TM30 like this... how can identify the antenna is operate the above said mode? can any one explain...

08 July 2024 6,609 2 View

How to give excitation to Crossed Dipole Antenna in HFSS?

I'm attempting to simulate a crossed dipole antenna. For excitation, I've placed a lumped port along each dipole. However, the resulting radiation pattern is similar to that of a single dipole....

08 July 2024 1,876 3 View

What's wrong with my COMSOL model for turbulent flow in time dependent solver?

I am trying to simulate velocity field inside a domain of just ambient air (pressure is 1 atm & velocity is 10 m/s). There is a tank inside it which has a leakage. The leakage hole is leaking...

01 July 2024 2,249 0 View