Network simulation for wireless sensor network?

More Vaseem Akram Shaik's questions See All

Does anyone know, can i do cryosectioning of whole aorta after oil red O staining and use the cryosection parts for further analysis?

I would like to quantify the lesions on aorta. I want to take image of atherosclerotic plaques formation in aorta by using O red Oil Solution. After the staining, what will be the storage...

16 February 2021 5,876 2 View

What is the best concentration of Pam3CSK4 to coat a dish to activate with THP-1?

Hi everyone I am trying to coat a glass-bottom dish with Pam3CSK4 and plate THP-1 cells to measure IL6 with ELISA from the supernatant. I wondered if anyone knows a good concentration and...

21 January 2021 2,593 1 View

How to interface Semi conductor physics and Fluid flow physics in COMSOL?. What are the parameters to be considered while we interface them?

I am using a silicon nano wire in microfluidic channel to identify the some changes in parameters like voltage and current. but i am unable to interface them. the two physics run individually but...

10 January 2021 8,894 1 View

Is there any analytical model to asses impact of rigid projectile on monolithic deformable plate?

I am trying to select suitable element type (Solid or Shell) for impact analysis. I have tried with both solid and shell elements. The results are same for both element types up to certain impact...

08 January 2021 3,251 4 View

Why internal energy absorbed during impact is different when simulated with solid and shell elements using abaqus?

I am trying to simulate high velocity impact of rigid spherical projectile on a rectangular plate using Abaqus Dynamic Explicit. Particulars of Projectile Diameter : 12 mm Mass : 7.05g,...

04 January 2021 10,022 3 View

Can anyone suggest how to find proper OFDM MIMO Simulink model ?

I am doing my research on a communication system. I need a Simulink model with MIMO OFDM anyone of you could suggest me to find the total OFDM transmitter and OFDM receiver Simulink design model

21 December 2020 3,709 1 View

Why I see Lamp-1 GFP in cytocol after transfection?

Hi every one I transfected Lamp-1 GFP plasmid to the HEK293 cell line. When I image the cells in TIRF, I see green fluorescence o the cytosol too. Does anyone have any idea that how it can...

21 December 2020 9,978 3 View

Why HEK293 transfected with LAMP-1GFP do not load dextran?

Hi every one I have made a cell line of HEK293 transfected LAPM-1GFP and after seeding the cells for 24h, I try to load dextran on the dish but after imaging, the cells with GFP+ have loaded less...

14 December 2020 1,801 2 View

What are the tools or software which can simulate climate change for a city and conclude future climate data?

I am working in research on climate adaptation so need to compare the performance of the urban fabric to the climate changes, which requires me to make a comparison and simulation of the...

03 December 2020 988 8 View

Correlation, Regression and significance?

Dears, I have different variables in multiple regression. Two variables are highly correlated. To solve the collinearity issue, I dropped one of them from the multiple regression model. The...

29 November 2020 2,695 4 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

Adel. A Ahmed Abdullah

There are many simulation tools (open source) that can simulate WSN such as: NS-2, NS-3, Omnet, etc.

Ali H. Wheeb

ns2 or oment can be used to simulate wsn. check both then chose one

Nitin Gupta

You can go for Omnet ++ or NS2 NS3. If you can have paid software than go for NETSIM

Vaseem Akram Shaik

@Akash Mondal: how to simulate Lora network in opnet.