Hello Everyone,
Thanks for the community help, I would like to know if anyone have the Ti-6Al-4V ICCD or JCPDS file.
Thanks in advance
Search here for Ti: http://www.crystallography.net/cod/
you will receive hcp and bcc, and these files you need for Ti-6Al-4V
if you have reliable lattice parameters from the literature, edit the files in Notepad and change lattice parameters.
If you need to be over-correct, add Al and V at the same positions as Ti and change occupancies according to atomic percentage.
Mubasher Ali Your obtained peaks may be matched with JCPDS data cards no. 75-1752 (TiO2), 44-1294 (αTi), and 44-1288 (β Ti).
I hope these are helpful for you. Best Regards
Alvena Shahid Thank you so much for the help. Appreciated
Most welcome Mubasher Ali, I hope these JCPDS cards are helpful for you.
Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...
10 August 2024 8,992 0 View
How can we differentiate between calcite, dolomite, siderite, magnesite and ankerite minerals in carbonatite rocks in thin section under optical microscope?
07 August 2024 2,132 3 View
Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...
07 August 2024 3,218 4 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?
06 August 2024 980 5 View
I would like to perform transfection with the reagent DharmaFECT Duo (Horizon) on the AGS cell line. Could you please inform me of the optimal concentration to use without causing cytotoxicity in...
03 August 2024 3,851 1 View
I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...
03 August 2024 6,070 3 View
I am conducting a qualitative study that uses interviews to investigate the perceptions of teachers about a particular leadership practice and I am focusing on 3 schools which have a total number...
01 August 2024 8,457 10 View
Hello I am conducting a microstructural analysis of a soil treated with lime. The following sem images are of the untreated s1 and treated soil s3. The untreated soil contains quartz calcite...
01 August 2024 572 0 View
HI there, I've came across several articles discuss about random audit an Non random to tax evasion or compliance. Most of the articles is relating about effect of audit (random or non random)...
31 July 2024 5,309 7 View
Require for Rietveld refinement in XRD.
08 August 2024 3,081 2 View
Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...
07 August 2024 9,563 0 View
Dear Researchers Kindly share JCPDS 65-7246 file Thanks in advance
04 August 2024 5,613 1 View
I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.
02 August 2024 6,789 4 View
How select composition for ods-high entropy alloys?
31 July 2024 2,795 1 View
Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...
30 July 2024 3,849 0 View
Any suggestions with respect to etchant composition and holding time?
27 July 2024 6,925 2 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...
13 July 2024 9,003 2 View
Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...
13 July 2024 2,417 1 View