The paper deals with the manufacture of various nanomaterials by sputtering with different targets
Please explain your query in very much elaborated manner. Then I can help you.
Good luck.
Which materials and targets?
You might need to Cosputter from different targets at the same time
Can everyone help me why in low doses of a drug grow impurity, but for the same drug in higher dose we have no impurity with over time?
18 January 2024 1,108 1 View
We have a problem with Diltiazem 60 tablets. We have the Dissolution profile of Diltiazem tablet cores according to the USP monograph (Diltiazem Hydrochloride Tablets). Tablet cores passed the...
01 September 2023 8,300 1 View
"Dear researchers and experts, I am currently conducting a study on the transfer of contamination from landfill leachate to groundwater and its subsequent discharge at an outlet spring. In order...
23 June 2023 8,844 0 View
Hi all, I'm trying to CoIP endogenous Miro1 and 2 proteins in HeLa cells. They are mitochondrial protein and isoform of each other. We suppose that Miro proteins interact with each other and I...
13 March 2023 3,947 0 View
we have a 20 microliter volume loop, but i want to use more volume loop because of more injection volume
31 January 2023 5,222 5 View
Can someone explain the following terms? ethanol (2X): what is alternative case it? PTFE membrane with a 0.45 micro meter pore size: what is alternative case it? polyester fiber (Carpenter Co.):...
24 December 2022 408 1 View
Hello How can I get a license to own feflow software? I live in Iran and due to sanctions and economic conditions, I do not have access to this software if I need it to continue my research. Thank...
19 November 2022 4,805 1 View
Hi I need a valid reference for the normal osmolality range of erythropoietin. Can you help me in this regard?
29 August 2022 6,381 0 View
Do you have a reliable protocol for viewing Total protein Spirulina on sds page gel?
26 May 2022 4,042 0 View
Hello everyone I inoculated C57BL/6 mice with TRAMPC2. I saw ulceration after 32 days of inoculation. anyone knows why it happens? except of injection manner, is there another factor to make this...
22 January 2022 2,596 3 View
I need to do some experiment with it in liquid form.
07 August 2024 613 3 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
I am experiencing this for the Bi2Se3 sputtering target. Initially, even if the target was 2:3 in Bi : Se, with a few sputtering runs, due to the high escaping tendency of selenium, the top layer...
23 July 2024 1,649 1 View
Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...
21 July 2024 1,680 2 View
We are fabricating a tandem structure where a ~50 nm thick WO3 film is deposited between two metal films using DC sputtering. We use a mixture of Ar and O2 gases at different flow rates while...
01 July 2024 2,686 2 View
I am fabricating the Hall bar (5 micron width and 35 micron length) of Ta(3nm)Co(4nm)Pt(5nm) using photolithoghaphy and sputtering. This Hall bar is connected by contact pads of Ti(10nm)/Au(60nm)...
29 June 2024 2,079 3 View
Using magnetron sputtering with an alloy target composed of A:B:C in a 2:1:1 ratio, the resulting thin film composition is A:B:C=1:1:1. How can you achieve a A:B:C=2:1:1 composition? What are some...
24 June 2024 1,605 0 View
We have observed many holes on the surface of TiO2. These holes have a diameter of approximately 1 µm and a depth of about 30 nm. The formation of these holes is mainly related to the...
20 June 2024 3,861 1 View
I conducted GIXRD measurements after performing O2 plasma treatment on a Cu surface. It was observed that the baseline is significantly high at low angles (10-30 degrees). What could this...
18 June 2024 2,996 3 View
I used material studio app dmol3 module for geometry optimization for a nanotube, and then I calculated its energy, for some of gas phases and I actually had the outmol file which allows me to...
14 June 2024 5,636 0 View