Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

How can we raise the figure when we writing a paper with Latex ?

Hi, everyone. I'm a starter to write a paper by Latex. But I have some difficulty using it. I'm writing the paper with 2 columns. And, there is one figure that occupies the 2 both-sides. I want to...

26 February 2021 3,738 3 View

Satellite orbit estimation using Recurrent Neural Network - what should I use?

Hello, I am a master's student studying in Yonsei Univeristy, Korea. I am trying to estimate the state of satellite, using Neural Network. Below is a simple flow of my study. 1. Train (t0 ~ t1)...

23 February 2021 6,383 3 View

What is the system of units used in the thermal conductivity by Spitzer and Harm?

23 February 2021 9,253 1 View

How many days do we need to detect adoptively transferred Treg in the tumor site in tumor-bearing recipient mice?

Hello, I've got a plan to isolate mouse splenic Treg (WT and KO of target gene) and inject these CD45.2 Treg into tumor-bearing CD45.1 mice. My question is how many days do I need to wait to see...

11 February 2021 8,238 1 View

Is it possible to antibody labeling with FITC cause antibody disfuction?

Hello, I studied how much bound my test antibodies to the target antigen using FITC labeling to test antibodies. I tested 3 types of antibodies, the elisa binding affinity and cytotoxicity...

07 February 2021 8,335 2 View

Can you use MTS assay with cells cultured in media containing phenol red?

I am trying to run a cell viability assay with LN229, but these cells are cultured in DMEM which contain phenol red. Is the MTS assay sensitive to the additional of phenol red in the media? If so,...

03 February 2021 9,478 2 View

Lighting for open field test behavior assay?

I am currently setting up our lab's behavioral space to run the open field test in rats, and I am trying to figure out how to set up lighting to evenly illuminate the open field chamber (a 90 cm x...

26 January 2021 1,399 3 View

Is there a surface inactive water-soluble dye?

Hi guys, I'm looking for a water-soluble dye which is not surface inactive in order to observe (water in oil) emulsions; I don't prefer to use oil-soluble dyes. I've used rhodamin123,...

21 January 2021 8,496 2 View

Can I calculate the average from the data which are collected every 30 minutes for ANOVA?

I artifically elevated the air temperature in the heated plot by 3-celsius degree compared to that in the control for 7 days. I want to figure out the effect of the temperature manipulation on...

21 January 2021 1,185 8 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

absorption= 1-mag(S(FP1:1,FP1:1)*S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)*S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

How can I calculate the magnetic force applied from a magnet (no electrism)?

I would like to calculate the magnetic force on a Fe304 particle which is into a liquid solution . The magnet is above the solution , and there is no electricity. I found this formula : F = (V...

13 February 2021 4,770 3 View

What is the best way to do symmetry in ANSYS Fluent for flow between two concentric cylinders ?

I am working on Taylor Couette flow between concentric cylinders and the results are correct for the full case. however, I wanted to do symmetry case to improve the mesh. I have tried periodic...

11 February 2021 2,193 6 View

What is the ideal value of UACI for image encryption scheme?

UACI - Unified Averaged Changed Intensity between cipher images. Why some papers refer ideal value to be 33.33 and some refer it to be 33.46? Which is the correct value? (In reference to image...

11 February 2021 9,562 2 View