Most powerful finite elements manufacturing processes software

Majid Midhat Saeed @Majid-Saeed

01 January 1970 0 5K Report

What are the most powerful software for simulation and solving manufacturing processes problems?

1 deform 3d

2 ansys

3 comsol

3 abacus

Badges
Science topic

More Majid Midhat Saeed's questions See All

Selecting particular columns from large datasets (csv) using R Studio?

So I have large number of csv files (100+) in a directory with same structure and column names. The data is in time series and there are approx 30 columns/file. However i only want to aggregate...

08 February 2021 245 5 View

Is it possible to export mesh from abaqus for using in Ansys Fluent?

Hi everyone, I want to mesh a part in Abaqus for further use in ANSYS Fluent because this way, it is much easier and faster to get a high-quality mesh. Is it even possible to generate a file...

15 January 2021 5,665 3 View

What are the (extrinsic) factors that influence the citation rate of a research article?

Dear RG members, Excluding the (intrinsic) factors such as quality and content of an article, what are the extrinsic factors/predicors that influence the citation rate of a research article? Is...

07 January 2021 3,410 3 View

Natural frequency extraction with ABAQUS?

I have modeled the RC beam with simply supported BC and I have got the frequency value for the case of the beam, but I have 150 modes for each analysis and I have to see them one by one to find...

05 January 2021 8,626 3 View

How high is the saturation electric field of P-E loop in Relaxor Ferroelectrics?

I have prepared a relaxor ferroelectric (KNN - BZZ solid solution) bulk sample. During P - E loop measurements, we experienced saturation electric field of about 100 kV/cm before dielectric break....

29 December 2020 9,080 3 View

What is the best way to simulate the fractional controllers?

What software do you prefer?

29 December 2020 889 3 View

How much pre-PCR dilution of mixed-template DNA extracted from pollen (honey) is appropriate for Metabarcoding?

I'm working on pollen DNA metabarcoding to identify the floral composition of honey. How much pre-PCR dilution of mixed-template DNA extracted from pollen (honey) is appropriate for the...

28 December 2020 9,132 1 View

How to add two vertical and parallel Fresnel reflection coefficients to retrieve overall reflection coefficient for a right hand circular wave?

I have a problem in which a right hand circular polarized wave (GPS wave) encounters an ideal smooth plane obliquely, and then is reflected off that. To solve this kind of problems, the wave is...

28 December 2020 2,271 3 View

Which is better to focus on teaching or research for a good academic life and Why?

Which is better to focus on teaching or research for For a good academic life and Why?

26 December 2020 5,737 9 View

Is ag paste suitable for back contact on silicon wafer? or i should deposit al on the back surface using pvd or plasma sputtering?

Fabricating silicon solar cell

22 December 2020 4,906 7 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is there a classification scheme for rock cavities or caverns with respect to their size and shape?

The range of forms and sizes of cavities in rock is very big. Is there a classification scheme for rock cavities regarding their size and shape?

02 March 2021 4,511 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

Which is the most convenient manufacturing software for Additive Manufacturing?

Which tools can be used to generate machine codes for additive manufacturing?

02 March 2021 7,220 2 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View