Modelling TL conductor by code-word in PSCAD?

More Pouriya Boostani's questions See All

What is the difference between quantum yield and quantum efficiency in solar cells?

what is the difference between quantum yield and quantum efficiency in solar cells? Actually not in general, specifically for solar cells and photovoltaics. Are the measurement systems diverse?...

02 November 2022 3,371 0 View

How can I coat PDMS to enhance adhesion of primary mouse stem cells to the surface?

Hi everyone, I'm seeding primary mouse stem cells into my PDMS-based organ on a chip device. However, the cells do not stick. We have tried coating the chip using 1: 100 and 1:20 Collagen, 2%...

09 December 2021 5,104 0 View

Clarke's transform of phase model TL in PSCAD?

Is it required to employ the clarke's transformation to decouple the voltages and currents of the 'frequency dependent (phase) model' transmission line in PSCAD software? Regards, Pouriya

13 November 2018 4,665 2 View

What is the relationship between chlorophyll meter readings and total nitrogen content?

Hello everyone, Please help me about nitrogen content in leaves. Sincerely, Gharavi

29 June 2015 2,615 10 View

What is the best way to calculate pigment content in calendula officinalis?

Hello every one, I want to calculate pigment content in calendula officinalis. Please suggest me the best way. Thanks. Sincerely, Gharavi

29 June 2015 3,814 4 View

How do I calculate seed setting rate in calendula officinalis?

calendula officinalis or english marigold

02 June 2015 5,271 5 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View