How to model short fiber reinforced composite in ansys
Hi, Is it possible to give specified shear for the wall in Fluent. I have checked the manual and found that the wall can be modeled in the following ways (For VOF model, only adhesion contact...
05 June 2019 6,670 3 View
Hi, I am trying to simulate the mucus removal process using Fluent. I used multiphase model (air+mucus), simulation is working fine for the no-slip condition. In the realistic case, mucus will...
05 June 2019 3,938 1 View
Dear all, Any body know how to give stress strain curve with negative slope in abaqus
02 March 2019 1,962 4 View
Hi, How to calculate 3 components of j integral using domain integral method.
04 May 2017 3,768 2 View
Hi, Is it possible to calculate displacement gradient matrix from strain tensor and gauss point co- ordinates
03 April 2017 1,635 3 View
Hi, How to calculated the Orthocenter of the triangle with 3D vertices A(x1, y1, z1), B(x2, y2, z2) and C(x3, y3, z3)
02 March 2017 1,710 3 View
Hi, Anybody please explain. How phantom node method is used in Abaqus XFEM implementation for cutting the element during crack propagation
10 November 2016 10,241 0 View
Hi, What is the difference between Generalized Finite Element Method and Extended Finite Element Method.
10 November 2016 9,976 1 View
Hi, I am trying to install abaqus 6.14 (abaqus 2016) in my workstation (client machine) Error is coming while giving licence server, can anybody help me in resolving this error Error: Unable to...
08 September 2016 8,208 5 View
Hi Everyone, I am trying to simulate crack propagation in abaqus and validating with analytical solution I need suggestions regarding what factors can to be compared/ considered for validating...
07 August 2016 6,247 4 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
A Markov-like Model for Patient Progression" Markov Chain Monte Carlo (MCMC) Markov Chain Monte Carlo (MCMC) is a powerful computational technique used to draw samples from a probability...
05 August 2024 10,079 0 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...
04 August 2024 4,130 4 View