How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

RIA. How to measure?

When you use RIA, with a control the unknown sample with antibodies, you bare in mind the binding sites of the antibodies. However you still need to measure labelled antigen (radioactive) and not...

28 February 2021 2,133 3 View

Benefits of the 24 welled plate?

We have always used the 96 welled plate, the 48 welled plate but apparently there is much evidence on the 24 welled plate and above all its benefits.It states it is the same you would use on ELISA...

28 February 2021 1,149 1 View

How can I homogenize this data to make a meta-analysis?

Hi, I am doing a review and hopefully meta-analysis for my Master thesis but I have the following problems: - Some studies only give the difference between end trial and baseline data and other...

22 February 2021 1,115 4 View

Research Gate Does it help researches to publicize their scientific work ?

In my opinion, the RG site is useful in solving scientific problems and shows the researcher's ability. Besides, the separation of the H-index from the self-citations and the overall index is an...

22 February 2021 3,894 6 View

Monte Carlo simulation?

Hi, i am conducting a Monte Carlo simulation for my new distribution but the MSE values are increasing while the sample size increase, does any experience this issue before and what should i do...

22 February 2021 3,680 4 View

Which is the best software or programming language (user friendly) for analysing data?

I have a basic knowledge on Python, R and MATLAB in analysing data. Among those, which is the best and user friendly? Which one should I learn deeply to analyse data?N:B: I want to learn data...

20 February 2021 3,950 15 View

Why is my CFD problem (mini heat sink rectangular channel) not converging while having good quality mesh?

My CFD problem is having two interconnected rectangular channel, which is known as mini heat sink. I have already performed parallel flow inside of an interconnected mini heat sink. However, I...

19 February 2021 3,209 3 View

Is There are any idea to achieve H NMR signals for swollen compound ??

the samples are not completely soluble - just swelled the solvents that's mean the sample may be partially soluble any suggestion, please

16 February 2021 8,801 3 View

The reason of PMMA channels cracking?

07 February 2021 3,663 2 View

Lift off problem with Indium/Gold deposition?

Hi, I'm doing 5/40nm In/Au e-beam evaporation at rates 0.2A/s(for In),1A/s(Au) on lithographically(doubly coated 495k,950k PMMA e-beam resist) done Si substrate at base pressure 2e-6torr. I'm...

18 January 2021 7,550 4 View

How to choose a PMMA with the correct thickness IN E BEAM LITHO?

I try to pattern the gold layer around 2 nm-20nm on silicon, I used around 2000nm thickness (PMMA 950K A13), I tried to pattern five samples in total, but only one showed the pattern I wanted. I...

13 January 2021 7,710 1 View

Cleaning SGE Micro Channel Device?

Hello all, I have a 3-port SGE microchannel splitter in my Thermo Trace 1310 GC connected to an Isolink 2 combustion interface. My microchannel device is clogged and my flow is significantly...

29 December 2020 7,002 1 View

Is surface embrittlement unavoidable after spray coating with brittle powder ?

I am not an expert at materials science. However, when I look at the literature, I read a process called cold spraying. This process is basically spraying a ductile powder (e.g. copper) onto a...

07 December 2020 5,378 2 View

Why is my TiO2 sol milky?

@Krunal Dholiya has sent me this question which I post below so he can get the benefit of many experts. Dear, I am preparing a thin film using TiO2 sol but i m fasing problem, with time it is...

23 November 2020 1,188 2 View

How to make few mm (~4-5 mm) thick Poly(methyl methacrylate) film?

Hi, I'm aware that thin film of PMMA can be spin coated. But I'm more interested in making few mm thick PMMA which will act as a substrate. Please share your expertise on how this can be...

21 November 2020 4,561 10 View

Why when I use nanofluid, the temperature of the microchannel does not decrease compared to water?

Why does not the temperature at the base surface of the microchannel decrease relative to water when using nanofluids?

08 November 2020 3,347 3 View

What could I expect to happen if I dilute a solution of PMMA in chlorobenzene with acetone?

I received a bottle of PMMA in solution with no information about which solvent was used, so I started using acetone to dilute the original solution. I had not experienced any consequences or...

03 November 2020 4,065 4 View

How to show 2D plane particle distribution in DPM modeling?

Hi, I'm using DPM modeling for illustrating the flow mixing in a wavy microchannel. I can show 3D particle tracking, but I want to display particle distribution in 2D plane cross-sections. Does...

02 November 2020 5,095 2 View