Loops on outside of pressure hose

More Alan Coulson's questions See All

Is perforin 2 present in NK & CTL vertebrate lymphocytes?

Every reference to perforin in lymphocytes talks about perforin 1. Has any one demonstrated the continued presence of perforin 2, the original perforin, in vertebrate lymphocytes?

31 December 2018 930 0 View

Can anybody translate the reference section of D. Kovachev "Effect of PHA ...Paramecium...1980, journals.mu-varna 17 & where is ref 8?

I'm writing an article and need translation and reference number 8.

06 July 2018 2,508 6 View

Does anyone know of research where phytohemagglutinin was used on protozoa, especially protozoan parasites.?

My reason for asking this question has to do with the extreme difficulty that many humans have in resisting malaria. I suspect that part of the reason is that lymphocytes evolved from protozoa and...

10 November 2017 1,133 3 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

The HCP removal rate is lower than usual in concentration step, why?

Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...

11 July 2024 5,380 0 View

Pressure in Iron Iron Carbide?

What will be the pressure in Iron Iron-Carbide diagram? It is at atmospheric pressure?

05 July 2024 1,891 0 View

How to Perform Randall-Selitto Test (Paw Pressure Test) In Mice?

Hi All, My name is Sumaiya, a PhD student at the University of Queensland. I am looking for some suggestions on how to hold mice and perform Randall-Selitto Test by using Paw Pressure Randall...

30 June 2024 6,004 0 View

How do I dedicate my entire life in doing only one thing?

I would like to dedicate my entire life in doing only one activity alone and nothing else. How do I achieve it in this world full of unavoidable distractions and societal pressures?

24 June 2024 298 1 View

If modulus of elasticity is divided by any inertial or dynamic pressure (1/2rhov^2), is there any dimensionless number present to represent it?

While deriving for a momentum equation with elastic stress effects, I am planning to put a ratio between elastic modulus (in Pa) and dynamic pressure (in Pa) in a simplified form. I am not...

23 June 2024 8,059 1 View

Trying to find a copy of an original paper?

Despite many attempts I am still unable to find the original version of this paper and would appreciate if anyone can locate it for us: Baker PG, Haig G (1981) Metronidazole in the treatment of...

20 June 2024 5,448 3 View

Alan Coulson

A preliminary sketch is attached:

And does anyone know of a lubricant that would help in the process of putting on pressure hose, and more importantly in their removal. Trauma from finger nails may be the start of venous ulceration.

Does anyone know why we are supposed to remove pressure hose at night? It would seem to me this would be the best time to wear them.

And after the hose starts to work and the foot and leg are smaller, should we not be re-measuring to get a smaller size of hose?