Looking for papers that used Maxent/presence-only software to address large-scale questions (state-wide, county-wide, range-wide, etc)?

More Ashleigh B. Cable's questions See All

How to calculate GRF/GRM from kinematic data?

I have a set of joint kinematics, collected via 3D mocap. I do not have any corresponding GRF/GRM data. Is there a way to calculate the GRF/GRMs from the kinematic data? I've seen some published...

09 January 2022 2,508 5 View

How to calculate multivariate outliers in jamovi?

I have performed a Pearson correlations for need for cognition scale scores (NCS) against each of the 3 sub-scales for multifactorial memory questionnaire (MMQ-Contentment, MMQ-Ability &...

13 November 2021 7,240 4 View

What is the appropriate statistical test for measuring the correlation between Need for cognition and MMQ?

Hi All, I'm currently developing a research proposal to explore the relationship between Need for Cognition and Subjective memory using the NCS and MMQ. My hypotheses are H1: A significant...

06 October 2021 421 5 View

In SDS-PAGE, if 2 entire lanes have more intense bands than the rest does this show increased protein expression?

I ran an SDS-PAGE gel of my total cell samples, each expressed in increasing concentrations of a co-factor to see whether this improves expression of the target protein. I coomassie stained the...

28 January 2020 1,899 3 View

Is it possible to thermal evaporate Aluminum onto itself to achieve greater thickness?

The maximum Al layer thickness my evaporator can produce is 0.6um. I would like to have an Aluminum layer thickness of about 5um. I am concerned about adhesion issues.

31 May 2018 8,142 5 View

Where do I start with encapsulation of hydrophobic drug into PLGA microspheres?

hi all, I am venturing into a new world for me, that of drug delivery. Does anyone have a comprehensive protocol for the encapsulation of a hydrophobic drug ( a steroid hormone) into PLGA MS? I...

19 July 2017 8,996 5 View

Analyzing EEGs with FFTs and PSDs

I am very new to analyzing EEGs and have a few questions about Fast Fourier Transformations (FFTs) and Power Spectral Densities (PSDs). I am conducting research that is looking at the effects of...

23 May 2017 2,464 2 View

Does anyone know where I can access POMS for adults or the BRUMS scale?

I am conducting research into the effects of different environmental conditions of exercise on anxiety and mood states. Unfortunately I am unable to find a copy of both the questionnaire and key...

10 December 2015 2,168 3 View

Does anyone have any experience in wheat anther culture?

I am looking for conditions, methods and media. I would like to grow anthers from early meiosis stage.

09 February 2015 6,083 3 View

Problems with eviews

I am trying to write a thesis on corporate governance and firm performance but I am having no luck on Eviews. I have watched every YouTube video and still no luck. I keep getting error messages....

01 January 1970 9,819 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Measuring the Intelligence of a Species?

Larger brains, which typically contain more neurons, store and transfer more information (Tehovnik and Chen 2015), but the precise relationship between number of neurons and information has yet to...

05 August 2024 1,238 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Why results of ROS flurescence are negative as there was no bacteria within?

Hello. I am working on ROS production of two systems: system A is cerium oxide and hydrogen peroxide, system B is cerium oxide nanoparticle, hydrogen peroxide and potassium bromide. I did some...

04 August 2024 5,974 3 View

Hein Van Gils

our paper covering Andalusia in Ecological Monitoring (Duque Lazo et al. 2016) fits your territorial admin unit and algorithm requirements.

Ilyas Nursamsi

Our paper covering a whole Southeast Asia region (Ahmad dwi setyawan et al. 2017), it may fits your desired teritorial wide.

Shivish Bhandari

Duque Lazo et al. 2016 would be a good for you. Thank you.

Lindsey E. Peavey Reeves

My master's thesis (Predicting Pelagic Habitat with Presence-only Data using Maximum Entropy for Olive Ridley Sea Turtles in the Eastern Tropical Pacific) is available here: https://pdfs.semanticscholar.org/ed5a/f8be7e4a358a5cb3cda19036525b6d91629c.pdf. This study covered the entire range of the turtle species.