Like Ansys, Fluent Software for various applications Is there any specific software for Energy and Exergy modeling of Thermodynamics cycles?

More Auroshis Rout's questions See All

What is the cost of transmission and cost of distribution of one unit of electricity in India, how to get the data?

In calculating Levelized unit cost of electricity it is very important.But where to get this one?Is there ant authentic data base or paper?

09 October 2017 5,876 3 View

Decentralized solar pv solution, is it viable as a permanent long term solution for India mostly in rural areas, if not what are the issues?

Main issues behind permanent solar energy solution in India

09 October 2017 4,735 10 View

Any good software to calculate and simulate levelized cost of electricity from power plants?

Any simulation based software to calculate LCE(generation) ?

09 October 2017 4,262 5 View

Can we use sand as a low temp sensible heat storage medium in solar thermal applications like solar water heater and others?

What is the value of specific heat of sand?

05 June 2017 1,310 3 View

Difference between COP and EER of an air conditioner?

I found from few sources that: 1.COP is unit less but EER has unit(BTU/Kwh) 2.In cop work input is Mechanical work but in EER Work input is electrical 3.COP=EER*0.293 Is this correct?If you have...

05 June 2017 1,189 3 View

In thermosyphonic solar water heater what is the max height up to which water will move up?

Is there any mathematical equation for that?

05 June 2017 9,360 4 View

Mode of heat transfer in this case between the top and bottom surface.

Gas is kept in a closed contained, side walls are insulated.Top surface is heated bottom one is cooled.

05 June 2017 1,962 4 View

What is the exactly the condition to be satisfied for a thermodynamic process to be identified as adiabatic?Is it q=0 or gamma=1.4(for air) or both?

I mean lets say there is a polytropic process with air having index n other than 1.4 but it is insulated such that q=0.Then can we term it as adiabatic. Another situation lets say for a given...

05 June 2017 1,791 3 View

What is the value of LMTD when temp diff is constant through out for a counter flow heat exchanger?It will be 0/0 indeterminate?

Suppose Thi=150, Tho=90,Tci=40, Tco=100 Value of LMTD?

05 June 2017 8,022 12 View

With load variation does the turbine shaft rotates with same speed or different equilibrium speed is achieved?

consider a hydroturibine as an example. suppose it is rotating at X rpm at a given load.Suppose load changed the new equilibrium speed(mass flow rate of working fluid changes wrt load) will be X...

04 May 2017 3,978 6 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Maurizio Pieve

once upon a time... there was CATT

What you may need is a software or a dll with fluid properties, then you'll able to generate your desired TD cycle. For example RefProp contains a good number of fluids. It is shareware

If I'm not wrong there is also the Gate cycle code, and maybe the Aspen Plus. As for this latter I'm not very sure

Auroshis Rout

Any feed back about axcycle?

Sorry I don't know