Less pellet during high copy plasmid isolation from maxi prep?

Nirmala Padmapriya Shnamugaganesan @Nirmala-Shnamugaganesan

05 July 2022 0 1K Report

I used qiagen maxi prep kit for plasmid isolation, but I have a issue in the pellet. Though it is a high copy number plasmid, very less pellet is obtained. Is there a reason for it?

Badges
Science topic

Similar topics
Phytochemistry
Extracts

More Nirmala Padmapriya Shnamugaganesan's questions See All

How to calculate CFU/m3 in settle plate?

14 July 2024 1,816 1 View

How do we connect Behavioural Economics, Emotional Models and Consumer Psychology to Design an Applied Neuromarketing Practice?

I would like to explores the connection between behavioural economics, emotional models, and consumer psychology to design an applied neuromarketing practice. The study aims to bridge the gap...

11 June 2023 1,536 9 View

Can anyone suggest me a good source to find LCI of smart box/energy box use in PV off-grid power system ?

Smartbox or energy is an important item of a solar power system. I would be grateful if someone can help me/suggest a literature source to find life cycle inventory of the smart box. Thanks.

25 November 2020 1,839 1 View

Can anyone suggest me a good literature source to find inventory data of rigid polyurethane sheet recycling ?

Polyurethane insulating foam plays key role in energy-efficient cooling systems such as storage in cold stores, local storage in supermarkets, and domestic refrigerators. In LCA assessment of...

13 November 2020 6,515 3 View

How to calculation refrigeration load of a direct solar drive refrigerator ?

In recent years a new development happened in solar refrigerator design by eliminating expensive and problematic energy storage batteries. The technology so-called, direct-drive refrigeration...

06 November 2020 3,367 3 View

Is it possible to get a small heater 30*30 mm size, which can work up to 200 degrees C?

Is it possible to get a small heater 30*30 mm size, which can work up to 200 degrees C? As part of my research, I need a small heater 30*30 mm size with the thermostat, which can work up to 200...

15 September 2020 8,987 3 View

I am working on circular polarization, can you help me how to plot axial ratio and radiation patterns for resonance frequency?

I am working on circular polarization, can you help me how to plot axial ratio with respect to frequency and radiation patterns for a resonance frequency?

24 April 2020 7,746 0 View

Is it possible to deposit YMnO3 thin films by e-beam technique?

I have YMnO3 (yttrium manganese oxide) in powder or pellet form.

09 December 2019 2,633 0 View

Design equations for microstrip lines?

I am working on designing of microstrip lines and its behavior with ebg structures. i am unable to find the design equations for microstip line length and width for a particular resonance frequency.

23 September 2019 5,773 1 View

Is it any software available for predicting the secondary structure for 3'UTR MicroRNA SNP's?

I am looking for any user friendly online tools for predicting the secondary structure for 3'UTR.

23 August 2019 2,380 7 View

Is there a problem with my RNA pellet?

Hello, I am currently having problems with RNA extraction. I am using mouse liver (C57BL6J), and I have extracted RNA from mouse liver before. Before this experiment, my final RNA pellets were...

11 August 2024 7,082 3 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

How to increase protein lysate concentration?

I am trying to prepare samples for IP. The pellet size is good and I am using 1% Tx-100 and using a syringe to further lyse the cells and maintain protein-protein interactions. I keep having a...

01 August 2024 7,199 1 View

What is the best practice for resuspending cell pellets during competent cell preparation (both electro and comp)?

I'm fairly new to making homemade comp cells and have done so with some mild success. What is generally an acceptable way of resuspending comp cells during wash steps? I've been told to swirl the...

31 July 2024 8,309 0 View

Pink bacterial colonies?

I am cloning an overexpression plasmid with my protein of interest tagged with mScarlet. After transforming my ligated product into DH5α bacteria and plating on LB agar, I noticed colonies with a...

22 July 2024 5,953 6 View

How to determine tannin content in fodder pellets?

22 July 2024 8,163 3 View

Why my plant protein cannot resolubilize after TCA/Acetone extraction?

I am extracting proteins from plant samples and am currently attempting to use the TCA/Acetone extraction method. I am having trouble resolubilizing my sample after drying the pellet. I collected...

15 July 2024 9,025 3 View

Which size of undersized iron pellet is suitable for sponge iron tunnel kiln production?

Someone advise me to use 1 to 2mm undersized pellet but it is not available. Do anyone have any experience in the field of tunnel kiln ?

28 June 2024 6,355 0 View

How to properly label fish feed pellets with stable isotopes for tracing C and N flow?

Hi, I´d like to trace the C and N flow in a recirculating aquaculture system by labelling the fish feed with concentrated stable isotopes. From a supplier, I found a product ouf of algae lysate...

19 June 2024 746 0 View

Can untransformed pET22b be isolated from five days old pellets stored at -20°C?

I've pelleted down the overnight ampicillin supplemented cultures of DH5ALPHA for pET22b isolation 5 days ago and stored them on -20°C without adding any buffer or glycerol. Would the cells be...

09 June 2024 6,479 2 View