Joint work in cancer modelling and treatment

More Kaushik Dehingia's questions See All

How to calculate Raman Spectra using VASP?

Is there any specific method to calculate raman spectra using vasp?

10 June 2024 872 1 View

Energy density calculation from Simulations?

I have calculated specific capacitance of the supercapacitor system but how can I calculate the energy density if I have data for capacitance at each provided voltage

10 May 2024 5,297 0 View

How many wild type of rodents for study of zoonotic diseases?

Please suggest how many rodents required for any study wild type rodents

04 April 2024 4,483 0 View

Motivational strategies used to promote learning in primary classrooms?

This study aims to investigate motivational tactics suitable for elementary classrooms, emphasizing their crucial role in shaping students' attitudes towards learning. It acknowledges the...

18 March 2024 7,625 1 View

We found a Raman peak in the silver powder around 1000 cm-1. What could be the origin of this peak?

As we know, for Raman spectroscopy, a change in dielectric constant is required w.r.t. phonons, which does not apply to metals. Therefore, pure metals are Raman inactive. Also, this 1000 cm-1 peak...

02 March 2024 1,856 4 View

OPLS AA force field angle coefficients?

I wanted to simulate ionic liquids using OPLS all atom force field unable to find the angle coefficients for the cations . can someone help me out?

29 December 2023 2,300 2 View

What shall be done in case most of the Vibrating Wire Instruments Installed in your dam are not working?

Vibrating wire instruments are installed for health monitoring during dam construction. But, with time, most instruments stop working and are useless. The continuous health monitoring of the dam...

04 December 2023 9,461 4 View

Integral capacitance to energy density?

Via MD simulations we have calculated integral capacitance for one electrode in a super capacitor system. Is it possible to calculate the energy density using this?

04 December 2023 1,794 1 View

How much electricity does a hand held 3D scanner use ?

What is the minimum amount of electricity consumed in scanning an object for five minutes

04 November 2023 8,954 0 View

How we can access the reference soil sample from any ecoregion (I need from southwest of Hungary)? #georeference #soil ?

A higher resolution is sought here. Any help or link which provide credible, georeferenced reference soil sample with chemical analysis will be better. The details will be used to publish an...

23 September 2023 4,084 6 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View

Zheng-Ming Gao

Is it relevant to machine learning? I am now working on intelligent information technology,, please let me know if anything I can help.

Babak Jamshidi

Hello Kaushik Dehingia You have my email. Please share more information on your project.

Kaushik Dehingia

Dear Zheng-Ming Gao

No, The work is related to "Dynamical system and computation of stability, bifurcation, optimal control".

If you are familiar with them then I can share with you.