SAP2000-V19
How could the SSI be activated in SAP2000? Do we have to assign the rigid connections for the columns bases like the fixed-base model?
Assuming running the undrained effective stress analysis in FLAC3D via Config FLUID using the effective stiffness and strength parameters, are we expecting the constant effective stresses in the...
06 July 2019 9,071 3 View
Is it possible to deactivate the effect of water so that FLAC adds the amount of steady state PWP to the effective stresses in all zones such that all the stresses in the soil constitutive model...
05 June 2019 5,384 2 View
The very initial step of each project is setting up the in-situ stresses. Right after the said step as well as amidst the dynamic analysis, could you cast light on how FLAC internally does the...
04 May 2019 2,363 1 View
Hey There. I am seeking a batch of references whereby the cohesion, friction angle, and dilatancy of the interface element, e.g., between a concrete foundation and the soil mass, could be...
02 March 2019 976 3 View
I was wondering what were the rationales behind making such an assumption in the soil mechanics and geotechnical earthquake engineering? Is it allowed to be used only in the static condition or it...
01 February 2019 4,206 1 View
Please find enclosed the attachment.
11 December 2018 9,592 1 View
PWP: Pore-Water Pressure
09 October 2018 2,513 0 View
I am wholly grateful to you if the Civil Engineering journal abbreviations source could be announced herein. TA! Navid
05 June 2018 1,350 2 View
The yielding stress of concrete material is considered to be the same as the characteristic compressive strength (fc0) of concrete.
05 June 2018 8,616 0 View
For instance, Rayhani and El Naggar (2008) posited that the said distance ought to be greater than five times of the superstructure width. Rayhani, M. H., & El Naggar, M. H. (2008). Numerical...
05 June 2018 674 4 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
How do soil microflora interact with plant roots and influence plant nutrition, health, and productivity?
06 August 2024 9,618 3 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View