PWP: Pore-Water Pressure
Assuming running the undrained effective stress analysis in FLAC3D via Config FLUID using the effective stiffness and strength parameters, are we expecting the constant effective stresses in the...
06 July 2019 8,943 3 View
Is it possible to deactivate the effect of water so that FLAC adds the amount of steady state PWP to the effective stresses in all zones such that all the stresses in the soil constitutive model...
05 June 2019 5,263 2 View
The very initial step of each project is setting up the in-situ stresses. Right after the said step as well as amidst the dynamic analysis, could you cast light on how FLAC internally does the...
04 May 2019 2,205 1 View
Hey There. I am seeking a batch of references whereby the cohesion, friction angle, and dilatancy of the interface element, e.g., between a concrete foundation and the soil mass, could be...
02 March 2019 808 3 View
I was wondering what were the rationales behind making such an assumption in the soil mechanics and geotechnical earthquake engineering? Is it allowed to be used only in the static condition or it...
01 February 2019 4,073 1 View
Please find enclosed the attachment.
11 December 2018 9,455 1 View
I am wholly grateful to you if the Civil Engineering journal abbreviations source could be announced herein. TA! Navid
05 June 2018 1,185 2 View
The yielding stress of concrete material is considered to be the same as the characteristic compressive strength (fc0) of concrete.
05 June 2018 8,489 0 View
For instance, Rayhani and El Naggar (2008) posited that the said distance ought to be greater than five times of the superstructure width. Rayhani, M. H., & El Naggar, M. H. (2008). Numerical...
05 June 2018 536 4 View
SAP2000-V19
04 May 2018 1,160 1 View
When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...
03 March 2021 4,892 5 View
We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...
03 March 2021 7,975 3 View
We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...
02 March 2021 6,036 1 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...
02 March 2021 3,309 2 View
It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...
02 March 2021 728 2 View
I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...
02 March 2021 5,829 1 View
Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...
01 March 2021 8,235 2 View
I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...
01 March 2021 6,985 3 View
I have used the i-Tasser several times, however it has been unavailable for several days. I tried the swiss-model, but the output was not very pleasant due to the model used. Is there any other...
28 February 2021 4,521 3 View
