Statistical analysis via Analysis of Variance (ANOVA)?

Hello Everyone I hope everyone is doing well. I have one article in revision process in Construction & Building Materials and reviewers' are asking to do statistical analysis. However, I...

31 October 2020 7,233 5 View

How the band gap in CNTs can be tunned?

CNTs can act as mettalic as well as semiconducting and I beleive that it can be controlled through band gap.

29 August 2020 9,765 9 View

Clinical Trail: How can we justify statistically a CT when it fails at final stage?

When a clinical trail succeed in first trails and fails at final trail,please write me, how could we justify the cause behind its failure statistically.

10 August 2020 8,035 3 View

Can all network UE decode the information transmitted by a eNB through Physical Downlink Control Channel (PDCCH)?

A wireless network consisting of two UEs (A & B) and an eNB. The eNB transmits control information to UE A through PDCCH. Can UE B also decode this information? Or is it permissible for UE B...

07 August 2020 2,628 2 View

What is the Distance Distribution of random point in a clustered environment?

How to find the distance distribution of a random point in a cluster from the origin? I have uniformly distributed cluster heads following the Poisson point process and users are deployed around...

04 March 2020 6,134 3 View

How to find the residual stresses in carbon fibre composites. Will XRD work for the same?

Respected all, I want to know about the correct method to find out the residual stresses in the carbon fibre reinforced composites. The literature says that XRD can get residual stresses. However,...

30 January 2020 486 13 View

Can you help in providing Support Vector Regression code for forecasting of solar power?

I have data on power generation and other variables (e.g Irradiance, temp & wind speed) of last two years(on daily basis). I want to forecast the power generation using SVR so I need its...

07 October 2019 4,541 2 View

How to remove DMSO from a solution?

I want to remove DMSO from a solution, without heating above 70C, DMSO we used to make solution with PANI.

15 September 2019 4,696 5 View

If the intensity of XRD peaks is very high about 500K, what does it mean?

i sysntesized sample by Ball milling and then heated it at 700 C, i got the pure phase with low intensities about 10K, then after annealing at 1000C, i got the intensities peaks about 100K-500K,...

18 July 2019 1,642 3 View

Can anybody help me in tracing the availiblity of some published articles?

08 January 2019 3,634 2 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

How can we limit artifacts caused by rotation in fiber photometry?

We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...

25 February 2021 568 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

How can we add reinforced thermoplastics with granules in injection molding machine?

I need to make an injection molding machine in which short fibers are to be introduced. Short fiber length and material properties are to be determined and also the material strength are to be...

22 February 2021 4,290 1 View

Staining methods for skeletal muscle fiber typing?

does anyone know the best method to differentiate and quantify rapid fatiguing and fatigue resistant muscle fibers? the old method form the 1980's uses ATP staining which is quite labor intense?

21 February 2021 6,483 3 View

Why the storage moduli E' decrease with highr fiber volume?

Hi guys, I am facing problems to interpret a DMA results. Material: Composite Bisphenol A + curaua fiber What is being tested: the influence of fiber volume on the composites properties...

12 February 2021 174 7 View

What is the reason of the received optical signal to be slimmed down in multi-mode fiber?

What is the reason of the received optical signal to be slimmed down in multi-mode fiber? I have 4 km multi-mode fiber

03 February 2021 1,105 10 View

Could any one help me with ABAQUS tutorials on fiber reinforced polymer concrete columns please?

I am modeling Carbon Fiber Reinforced polymer wrapped concrete column in Abaqus, but I have faced so many difficulties especially in the Model< Interaction and Constraint module. SO could you...

26 January 2021 6,795 4 View

How could I do a simulation for the energy consumption of a CNC machine?

I'm working on my dissertation and it is about how to save energy when a CNC machine goes to idle mode. (A concept model of the idle machine energy saving in industrial manufacturing...

26 January 2021 9,620 5 View

Dear Colleagues, I am looking for a way to dop of electrospining nanofibers on the HEPA filter.Someone can guide me?

Electrospining method is important for production of nanofiber .If doped with nanoparticles ,can be used for remove of contaminant such as VOC , but don't have mechanical strengh . For finding a...

24 January 2021 7,290 3 View