Can we use 3D printing resin in solution casting composite preparation method?

Danish Tahir @Danish-Tahir

10 May 2022 1 1K Report

I want to make a composite by using 3D printing resin as a matrix. I am using solution casting method.

Ali A. Al-Allaq

Yes , read the paper (3D printing of polymer matrix composites: A review and prospective)

Badges
Science topic

More Danish Tahir's questions See All

How to get article and literature review templates (for publishing) from websites like Elsevier?

Hello, I want to know how to get the templates from the Elsevier official website (their last updated if exists)? I would like to know the steps if possible.

26 July 2024 3,264 2 View

What is the cyclic deformation behaviour of plain low carbon lath martensite?

Dear RG Community, I am looking for some suggestions of good references wherein the cyclic deformation behavior (i.e. cyclic stress-strain curves and evolution of stress-amplitude with the number...

29 May 2024 3,202 4 View

Commercial Biotransformation with Microbes?

Hello, I am in search for papers that: 1) explain with graphs the biotransformation of diosgenin to cortisone. 2) explain with graphs the biotransformation of soybean oil to progesterone. If...

29 April 2024 1,333 3 View

Which regression analysis will be applied if there are 7 nominal dependent variables and 1 ordinal independent variable?

which regression analysis will be applied if there are 7 nominal dependent variables(YES/NO categories) and 1 ordinal independent variable(3 categories: Low, normal, high)?

23 April 2024 9,971 3 View

How to achieve a review paper when it claims all authors have passed away?

Name of literature review: Plastic and Human Health: A Micro Issue? May 2017 Environmental Science and Technology 51(12) DOI: 10.1021/acs.est.7b00423

21 April 2024 1,589 3 View

How to form pn junction in tandem solar cell and its sturture?

17 April 2024 7,715 1 View

Can autodock vina give more than 10 conformations with minimum binding energies?

I want to increase the number of conformations which is by default 10. I want to get 100 conformations of a single ligand. Is it possible using autodock vina or any other software?

11 April 2024 8,736 2 View

How to expression and purify full length TRAF2 protein from bacteria?

Hi, I am for the first time struggling with TRAF2 full length protein purification from BL21 or Gold but I fail to purify it although I tried GST, MBP and His tag it the N- terminal. Do any...

07 April 2024 1,090 0 View

How to dock ZIF-8 (MOF) with drug doxorubicin?

Hello there! I am trying to dock ZIF-8 (MOF) with the drug doxorubicin using PyRx and discovery studio for visualization of results. My queries are: 1. When I convert .cif file to .pdb using...

27 March 2024 2,007 4 View

Maestro Desmond Schrodinger problem in protein preparation wizard?

Dear Experts I downloaded and installed the Desmond Schrodinger software in my Linux system. installation was fine and when i tried to prepare the protein in protein preparation wizard I noticed...

28 December 2023 1,696 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

How to find a reaction is reversible or irreversible in CV? How to know the number of electrons transfer?

My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...

30 July 2024 4,671 3 View

CAD File of human's & rat's respiratory airways ?

Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...

29 July 2024 1,092 2 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

A positively charged and 10x his-tagged protein that doesn't bind to any chromatographic resin?

Hello everyone, I am currently working on a protein that is 10x his-tagged and positively charged (predicted pI=10.16). But when I tried to use Ni-NTA column to purify the protein, it's not...

24 July 2024 7,293 4 View

What is the principle/mechanism behind aging of carbon (graphite) containing refractory mix for isostatically pressed refractories?

The resin bonded carbon containing refractories are aged before use. How time of aging is determined? And mechanism behind aging.

23 July 2024 3,205 0 View

Prevent sedimentation and maintain the suspension of powder particles in the resin ?

Hello, I am experiencing an issue with mixing micro powder with resin in a 3D printer. The problem is that sedimentation occurs after a short period (about half an hour to an hour). Could you...

23 July 2024 1,672 0 View