How can I isolate cell products deposited on the glassware?

Say I've grown cells on a petri plate and they have deposited their extracellular matrix onto the petri plate. Say I've decellularised it and washed away all the cells. Now is it possible to...

01 February 2019 3,287 3 View

What is the procedure for production of absorbable PGA or PLA sutures?

I wanted to know the procedure of production of absorbable sutures (PGA or PLA) including their composition and concentration of the polymer. I also want to know the time it takes to decompose in...

31 December 2018 1,760 0 View

Electrospinning in Bangalore

05 June 2017 2,758 4 View

How to extract Extracellular Matrix?

How can I extract extracellular matrix from a pig's bladder? Is there any other source or an easier option?

31 December 2016 3,964 2 View

What happens when excess of Extracellular Matrix Patch or Powder is used to treat a wound?

I heard about Extracellular Matrix Patch and Powder being used for treating wounds and some also being used in surgeries, I wanted to know what happens when excess of it is used? For example: I...

11 December 2016 9,841 2 View

Alternative to trypsin

Can I use 0.05%EDTA or 0.05%NaN3 instead of 0.02%Trypsin to remove a few proteins from my test tissue? If so then what will the difference in the result that I get be? Are there any alternatives...

01 January 1970 8,629 2 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

No title

02 March 2021 3,060 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View