Is there any freeware or webserver to predict chemical descriptors for a set of molecules and not one by one molecules??

More Manikanta Murahari's questions See All

How to perform static structural analysis in ansys to calculate Gear body & Gear tooth deformation due to rotational speed?

I would like to calculate the gear wheel and gear tooth deformation due to rotational speed? The gear shaft is mounted on hydrodynamic bearings. What are the boundary conditions need to apply?...

21 May 2024 8,067 0 View

Can we calibrate and validate the SWAT model using a single subbasin within our watershed?

at the endpoint of the watershed. The Gaging point is not there.

06 February 2024 2,678 2 View

What is the emissivity of 17CrNiMo6 at 50 deg C to 150 deg C?

I would like to set the emissivity of the infrared thermometer to measure the temperature. What is the emissivity of the material 17CrNiMo6 at 50 deg C to 150 deg C?

29 September 2023 5,879 0 View

Thermoelectrical property relations for high entropy alloys?

Dear Researchers, I am currently seeking information on estimating Resistivity and Seebeck coefficient for high entropy alloys. While I have come across equations for binary alloy systems, but...

27 June 2023 7,978 2 View

How to calculate sliding friction coefficient using elasto-hydrodynamic lubrication?

I would like to simulate the heat generation in helical gears. I need to calculate friction coefficient, contact stress and sliding velocity. How to calculate friction coefficient?

01 June 2023 8,524 0 View

Simulation of heat loss in oil-jet lubricated helical gears?

Heat is generated in the helical gears due to sliding friction. Helical gears are oil-jet lubricated and cooled to reduce the gears temperature due to heat generation. I would like to estimate the...

30 May 2023 5,927 0 View

How to estimate gearbox power loss ?

How to calculate gearbox power loss? Example: A 30 MW gearbox, the helical gear pair mounted on journal bearing. It is rotating at high speeds (greater than 120 m/s). power losses are mesh power...

16 May 2023 4,643 2 View

Can anyone sugguest a way for increasing significant figures in docking score of autodock vina??

We did a virtual screening of database using autodock vina. We started ranking the molecules based on docking score and observed three molecules of different chemical structure with same docking...

15 May 2023 7,436 4 View

How to measure gear teeth temperature?

Are there any methods available to measure gear teeth temperature? What are the instruments/sensors used to measure it? Any simple methods (contact and non-contact type) available to measure gear...

16 April 2023 3,465 0 View

How the minimum clearance is selected for any kind of hydrodynamic journal bearing?

How to select minimum clearance for hydrodynamic journal bearings, especially offset and elliptical bearings?

31 March 2023 3,458 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Are there instances where molecules with larger molecular weights exhibit greater mobility than those with smaller molecular weights?

Hi, I know that low molecular weight (MW) molecules generally tend to have higher mobility, while high molecular weight molecules tend to have lower mobility. However, in my experimental...

06 August 2024 1,495 2 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

For an in-vitro drug release study, what molecular weight cut-off (MWCO) dialysis bag is required for a 117 kDa protein?

kindly reply me. Thanking you in advance.

05 August 2024 7,727 4 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

Can anyone provide me with molecular docking softwares/ websites?

Molecular docking software/ websites?

02 August 2024 8,704 7 View

Can't spin-orbit coupling(SOC) be included in optical properties calculation in CASTEP?

I am currently using CASTEP version 2020. When I want to run optical properties calculations with spin-orbit coupling(SOC), I encounter the following error in a pop-up window before the job gets...

02 August 2024 2,890 0 View

CAD File of human's & rat's respiratory airways ?

Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...

29 July 2024 1,092 2 View

Dr Thirumal Kumar D

http://www.yapcwsoft.com/dd/padeldescriptor/

https://www.softpedia.com/get/Science-CAD/ODDescriptors.shtml

https://cdk.github.io/

https://sourceforge.net/projects/joelib/

Manikanta Murahari

Dr Thirumal Kumar D Thank you very much.

Dr Thirumal Kumar D I was able to retrieve 1D, 2D and fingerprint descriptor from PaDEL. But finding difficult with 3D descriptors. Tried all possibilities. Can you please let me know process for the 3D descriptors using PaDEL.

Thanks in advance.