How to measure gear teeth temperature?

17 April 2023 0 3K Report

Are there any methods available to measure gear teeth temperature?

What are the instruments/sensors used to measure it?

Any simple methods (contact and non-contact type) available to measure gear teeth temperature? contact and non-contact type

Badges
Science topic

More Manikanta Reddy's questions See All

Dear all, Iam currently working on Dc Microgrid model for electrical vehicle charging. Can any body give good IEEE research paper on this topic?

please give any suggestion?

04 February 2021 4,837 5 View

What does the change in D-peak position in Raman spectroscopy of carbon materials indicates?

We have carried out high-pressure Raman characterization on some of our samples. After fitting, I have observed a change in D-peak position with increasing pressure. What does this change...

20 January 2021 853 3 View

PSFB control signal?

Hi everyone iam facing a problem to give control signal for switches in design of PSFB converter in matlab simulink. Anybody's help will be appreciated.

14 December 2020 6,021 3 View

What are the alternative to the pozzolanic materials to in concrete to enhance the durability of concrete?

As of now, Only industrial wastes were using as pozzolanic materials in concrete to enhance the durability of concrete. Can any once suggest me the alternatives of those materials?

11 October 2020 3,569 4 View

Can any one suggest me the dielectric constant of Gold and Co3O4 at room temperature ?

i have a question regarding dielectric constant of gold,cobalt oxide (co3O4) and n-tpe silicon . i find only one publication on this issue showing dielectric function cobalt oxide(CoO) 12.9 and...

02 October 2020 9,138 4 View

Eupergit beads for enzyme immobilization?

We are looking to immobilize some of our enzymes on Eupergit beads. I was wondering if you know any commercial supplier of Eupergit beads?

28 September 2020 5,664 3 View

Can somebody kindly suggest a good FEM software for the numerical solution of stochastic PDEs?

Please kindly suggest some good FEM softwares for the numerical solution of both time-dependent and time-independent stochastic PDEs.

28 September 2020 6,598 4 View

How to run Seismic analysis for the following model in OpenSees..?

I have developed a 3 bay 5 story 2D frame in Opensees but I have problems with element load and application of seismic load in Opensees using an acceleration file. I always got an error namely...

27 September 2020 5,885 4 View

How can we evaluate the conductance of a constant power load (CPL)?

Any CPL is modeled with a current source in parallel with negative resistance. How do we evaluate the negative resistance, if we know the constant power consumed by the load?

19 September 2020 6,188 3 View

How to learn the modelling of RC beam subjected to 4 point bending in Ansys Mechanical APDL?

I need to model a reinforced concrete beam subjected to 4 point bending. I also need to plot the load vs displacement at mid span and compare it with the experimental data. Bond between concrete...

10 September 2020 9,004 4 View

Is this the fragment of a sauropod tooth?

Dear colleagues. Fragments of this species are very rare from a terrestrial Lower Cretaceous locality from Germany. Up to now from this locality sauropods could not be proved with certainty. Other...

14 February 2021 2,310 1 View

Gear reduction for back-drivability of a motor?

Hi everyone, Does anyone know up to what reduction ratio of gear does a motor remain back-drivable? I want my robot to have safe interactions with the environment and other humans. Can you give a...

26 December 2020 7,142 3 View

Carboniferous shark teeth - ID help?

Dear everyone! I am looking for some help regarding the identification of two Carboniferous shark teeth from Hungary. See the pic attached. I'd go for Bransonellidae family for A, and Falcatidae...

21 December 2020 1,226 4 View

What do you really feel about buying NISSIN dentofrom?

There are massive conflict and resistance among students to shift from low-speed teeth to high-speed teeth.

16 November 2020 8,826 100 View

Help in Sample Size Calculation for my Thesis Comparing the Clinical Outcome of Pulpotomy in Mature Permanent Teeth with MTA & EBRRM?

I am looking for assistance in finding statistics for sample size calculation on topic Comparing the Clinical Outcome of Complete Pulpotomy in Mature Permanent Teeth using MTA & Endosequence...

20 October 2020 8,197 6 View

Abaqus dynamic simulation - How to avoid parts penetrating to each other?

Hello, This is my first time using Abaqus to conduct a dynamic analysis. I'm trying to simulate drop test of a helicopter skid landing gear but the skid is not colliding to the ground but...

06 October 2020 7,844 4 View

How I can make a fatigue Analysis by Abaqus + FEsafe?

want to make a fatigue simulation on some mechanical parts like Gears, Bearing, and gear housing. please assume 2 gears in contact.when they Are rotating under constant torque and velocity the...

28 September 2020 8,132 3 View

How I can fix "unconnected regions warning" in Abaqus?

I want to simulate 4 gears in Abaqus and I made the model in Solidworks and in the true locations and positions. it is seems to be tangent in 3 points each 2 gears together. I checked the sketches...

22 April 2020 9,162 3 View

Is it possible to use only ten samples in the research?

Is it possible to use only ten samples in the research, knowing that my samples are cases of extracting teeth and then drawing blood to isolate bacteria and it is difficult to obtain the consent...

24 March 2020 4,775 2 View

Case depth and spallation of plasma nitrided steel?

We nitride 15-5PH stainless steel for aircraft landing gear at 405 degrees for 70 hours to get a case depth of 40 microns. We have noticed on testing that we get spallation and wear of the case....

13 January 2020 9,560 1 View