Is there any filament winding technique combined with other fabrication process to innovate a new or novel technique?

Quanjin Ma @Quanjin-Ma

27 December 2018 1 957 Report

Is any idea to combine othe composite fabrication processes with filament winding technique to break several obstacles.

Fares Mohammed Laid Rekbi

Article Experimental and numerical analysis of mode-I interlaminar f...

Badges
Science topic

More Quanjin Ma's questions See All

How can we improve storage conditions of museum objects?

90% of museum objects worldwide are in storage.

21 July 2024 8,038 6 View

How to removal of dead cells and debris from organoid cultures?

I'm currently working with human pancreatic organoids and I am wondering to remove the dead cells and debris from health organoids, any suggestions would be appreciated!

17 July 2024 8,330 1 View

Does it work as antibiotic resistance if plamid has no RBS??

I am on gene work to express gene of interest in some Bacillus species. Thus far, i need to try some RBS in Vector which is optimized for bacillus subtilis. Before i design vector to express in...

11 July 2024 7,847 1 View

Can a liquid metal-ligand sample be directly analyze in flame atomic absorption spectrosocopy?

Can I directly analyze a liquid metal-ligand sample without acid digestion in flame atomic absorption spectroscopy?

25 June 2024 1,866 2 View

Is this a mixed methods approach?

For my PhD dissertation: If Chapter 1 is a systematic literature review (QUANTS/QUALS) while Chapters 2, 3, and 4 are empirical chapters (QUALS), is this considered a mixed methods research...

16 June 2024 3,220 5 View

What can I do if primer solution gives band in electrophoresis before PCR reaction?

Trouble 1: I ran a PCR reaction and found a low molecular weight band (100 bp) when doing electrophoresis. 1ng plasmid (OD260/280=1.84) was used as template. Final concentration of primers was...

13 June 2024 5,540 6 View

How to find the original questionnaire of the article-Dimensional analysis of schoolchildren’s food label comprehension: a pilot study?

27 May 2024 2,551 0 View

Why the Mixed mode simulation always exit with status 0?

I encountered some issues while simulating the transient characteristics of a device using Mixed Mode. After executing the following codes, an error message "Simulator has unexpectedly exited with...

23 May 2024 2,238 0 View

Can bands of cell lysate be seen during SDS-PAGE?

I want to detect my target protein through WB and it worked well before. But now I could not get any signal for both my target and the GAPDH, so I ran SDS-PAGE. I expected many bands on the gel of...

23 May 2024 613 6 View

Can I ask for a JCPDS card no. 01-083-1436 or CPDS file number 00-031-1979 for urea?

Can I ask for a JCPDS card no. 01-083-1436 or CPDS file number 00-031-1979? I need to index a urea derivative compound to the face-centered tetragonal structure, JCPDS card no....

15 May 2024 9,751 2 View

Hello researchers, how can one get the optical density of a filamentous algae?

i am comparing the growth performances of filamentous and non filamentous forms. in a case where I can not count the cells of the filamentous algae using a hemocytometer, is it okay to do a...

30 July 2024 5,985 2 View

How do you decide an optimal AC amplitude for non-faradaic electrochemical impedance spectroscopy?

I work with planar interdigitated electrodes (IDEs). The finger width and the spacing between the fingers are 5 micron. The surface of the IDEs is coated by a non-conductive polymer layer...

16 July 2024 5,031 1 View

How to write literature review?

i want to write literature review on the topic " production of 3d PLA filament"

19 June 2024 1,712 2 View

Which solvent and substrate is found to be best suited for deposition of electrodes with MXene ink?

Suppose we have dried MXene slurry (Ti3C2Tx), then the combination of which solvent (in which this dried MXene slurry powder will be mixed, subsequently forming the "ink") and corresponding...

13 June 2024 5,763 0 View

Best method for extracting RNA from low biomass of Ectocarpus (filamentous brown algae)?

Hello everyone! I am currently working with the model organism Ectocarpus (filamentous brown algae). Our team is trying to standardize a protocol for RNA extraction using low biomass (around 10...

18 May 2024 3,862 1 View

Has anyone used the MEMS and Nanotechnology Exchage (MNX) foundry service?

I have been trying to contact them for about 2 weeks now and I have received no response. I am wondering if they are still active. If not, could anyone suggest a similar foundry service to do some...

12 May 2024 2,100 0 View

What is the meaning of depth and level in Imaris statistic analysis (filament function)?

I used filament tracing of Imaris to reconstruct dendritic spine and I got the statistic result of dendritic spine density. I wanted to count dendritic spine density in secondary and tertiary...

06 May 2024 8,675 0 View

The filament shows emission current while the filament is off?

Hello for everyone, I come to you to help me find a solution to my problem in the GC MSD.I reinstalled the external filaments but it does not work normally and an error message is displayed “The...

24 April 2024 361 2 View

What are the best welding configuration for welding a cylindrical tube to a flat surface?

I'm welding (laser welding) a nitinol cylindrical tube to a nitinol flat surface, and I am evaluating three methods for the laser welding configuration (as depicted below): I) using a groove on...

26 March 2024 4,006 6 View

How to count cells of a filamentous cyanobacteria with a Neubauer chamber ?

I would like to work with Nostoc punctiforme, which is filamentous, and try to assess its growth by cell counting using a Neubauer chamber. Does anyone have experience with this? Is it possible to...

24 March 2024 1,906 0 View