05 October 2016 3 8K Report

I need any emperical, or numerical, formulation of diffusion coefficient for Urea Water Soluble (UWS) into NOx (e.g. NO2).

More Mansour Al Qubeissi's questions See All
Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

Is there a fast method matching citations to bibliography (manually typed references)?

I need to be able to match in-text citations to a reference list and back again in very large documents (100+ pages) WITHOUT the use of referencing software like Endnote. my method is to type the...

27 February 2021 9,848 1 View

Can I put a figure that was drawn by Bio-Render in publication paper?

I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?

27 February 2021 8,179 1 View

What is the most suitable medium of ascomycetes fungi ??

What is the most suitable medium of ascomycetes fungi ??

26 February 2021 4,413 1 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Is it possible that Cancer cells could survive in heparinized blood for 48 hours?

Hi everyone, I am just wondering if we incubated 200 microliter of whole blood with 50 microliter of cancer cells(1bout 5000cells) do you think that cancer would survive for 48 hours?

23 February 2021 3,840 3 View

What is the most prevalent drug related problem in the developed countries?

Detecting the drug related problems is an important step in the pharmaceutical care plan

21 February 2021 5,421 3 View

What are the dimensions by which the independent variable (big data) can be measured, Knowing We using the questionnaire instrument?

We have a research project consisting of three variables where big data is the independent variable. Some previous studies showed that Volume, Variety, Velocity and Veracity Are the dimensions...

21 February 2021 8,133 2 View

Is nanotechnology part of materials science? Is it possible to obtain Pico technology and move from hypothesis to application?

Pico-scale This is three orders of magnitude smaller than a nanometer (and thus most nanotechnology) and two orders of magnitude smaller than most chemistry transformations and measurements. Pico...

18 February 2021 4,540 5 View

Similar questions and discussions
Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

How to remove fatty material from plant extract?

The resultant solid was partitioned three times with 250 ml of petroleum ether (40-60/c) to remove any fatty material and evaporated to dryness.

28 February 2021 9,464 2 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Has anyone used the Illumina ITS1 primer sets?

Hi everyone, Illumina provides a list of primers to amplify with high taxonomic coverage the ITS1 region for further fungal sequencing, but I cannot find the exact amount necessary of each...

25 February 2021 6,969 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

What is the error of the Txy diagram?

Hi, I know the attached Txy diagram has an error but can't figure it out. Could you please look at the diagrams and explain it to me?

23 February 2021 4,239 1 View

How the values of errors can be calculated for thermodynamic data?

I have calculated thermodynamic parameters for surfactant solutions in aqueous and mixed alcoholic solvents. I want to calculate the value of errors in the data and represent it in the table along...

22 February 2021 239 2 View

How to improve the adhesion between germanium and silicon monoxide thin film layers using EBEAM evaporation?

I want to deposit multilayer coating of germanium and silicon monoxide on silicon wafer using ebeam evaporation?

21 February 2021 2,141 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close