Is Near Infrared Spectroscopy calibration transferable from device to device?

More Shubham Rathore's questions See All

In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

Do you know any MR image dataset?

I would like to research on MR images (0.5T and 3T). Can you please suggest some websites that I can download dataset including both 0.5T and 3T MR images? Thank you.

02 March 2021 7,735 3 View

Where can find Medical Image Data Sets for Machine learning research project?

I want to work on medical image(disease) detection and classification. Where can I found Image data sets?

24 February 2021 3,130 3 View

IF troubleshooting: looking at an intracellular protein that localizes to the cell's and how to reduce increase in signal due to cell ruffles?

I am currently trying to stain for PI3KBeta in MDA-MB-231 cells. My current issue is that 1) beta stains all over the cell and 2) there is an increase in signal at the edge of the cell and this...

24 February 2021 8,582 1 View

What is your preference for journals for publishing in the field of Hyperspectral Imaging or Remote sensing?

I believe that we need to share our experience in publishing in the field of Hyperspectral Imaging or remote sensing? What is the best journal that you publish with? What is the worst experience...

23 February 2021 3,411 4 View

Interpretation of a fluorescence Emission spectrum ?

Hello, i work with a spectrometer which only render the fluorescence emission spectrum. Until now i just found how to interpret an exitation- and emission spectrum together to generate deeper...

20 February 2021 1,291 3 View

CT image preprocessing in python?

I have a 3D CT image of a car engine in raw form with no header information. When loaded into numpy array as 16 bit unsigned integer, I noticed that the values range between 0 to 52000. Is this...

15 February 2021 4,736 3 View

Hyperspectral Image : open, visualize, process in Python?

I am looking for a tutorial or course to learn how to open, visualize , process hyperspectral images in .hdr , .raw format using python. Any recommendation for a tutorial is appreciated ? Thank...

08 February 2021 7,896 3 View

FLIM Signal to noise ratio of a time series - can I use dark frames to measure noise?

I am doing an analysis on some FLIM data in the form of time series image stacks. I need their signal-to-noise ratio. Recording starts several picoseconds before the excitation pulse, so no sample...

08 February 2021 7,169 3 View

Could we interpret the intensity of the peaks of the FTIR spectrum correlating to the concentration of some compound?

If we analyze the extract of two plants from the same species (for example) and there are very similarities between the two IR spectra except for the intensity of one peak at the same wavenumber....

05 February 2021 2,630 5 View

Are the hyperspectral image datasets which are publicly available at ehu.eus website atmospherically and geometrically correct?

I've come across a couple of publicly available hyperspectral image datasets from the website http://www.ehu.eus/ccwintco/index.php/Hyperspectral_Remote_Sensing_Scenes Now, my concern is...

05 February 2021 3,550 1 View

Bojidarka B. Ivanova

Mr. Rathore,

It is not.

Kārlis Švirksts

In theory it should be possible, but in practice it is not due to many different things.

For example - NIR source wears out in time and that reduces spectral intensities of any sample scanned, if we ad calibration from a device with new source we would get lower amounts of compound due to lower spectral intensity.