Is it suitable to use drop casting method for depositing films of counter electrodes of DSSCs?

More Bulkesh Siwach's questions See All

When I read articles on renewable energy source, It comes everywhere that Sun provides 3X 1024 J energy per year to earth. Means How many joule?

I needs its explanation..Plz provide Regards

02 March 2018 1,290 3 View

What is the significance of cyclic voltammetry (CV) measurements in the field of counter electrodes for DSSCs?

I have prepared three carbon based electrodes like graphene, MWCNTs, GRAPHENE OXIDE etc. and need to note CV of these. Please tell is this measurement is necessary for these counter electrodes...

16 November 2017 2,797 2 View

How graphene makes bond with the TiO2 in tiO2/graphene nanocomposites? What should be the possible mechanism?

As i am synthesizing TiO2/graphene nanocomposites so want to know about the linkage mechanism.

15 March 2016 1,361 6 View

How to increase the adhrence and stability of thin films prepared by doctor blade method?

After heat treatment at 450 for half an hour..my films were not stick to ITO properly..they easily stick to hand if scretched...i have used PEG 20000 as binder and distl. water for making pastes...

03 February 2015 4,684 3 View

How can I trim the terminal oligonucleotide from EST sequences of a large datasets? (nearly 60,000 sequences to be trimmed)

I am working on an EST data assembly and annotation project. After screening with VecScreen no significant matches were detected. As a cautious step, we plan to trim the terminal 25-30 nt length...

11 May 2014 406 3 View

Can anyone help with cleaning of EST sequences?

I have started working on EST data processing of cotton. As a first step, we have screened all the deposited EST sequences by 'VecScreen' to detect vector sequence contamination. But in all the...

11 May 2014 7,156 3 View

How to calculate PIC, MI and H' values for ISSR primers?

We are working with SSR and ISSR primers. The resolving power of various SSR primers to distinguish among the genotypes could be evaluated by calculating PIC, Marker index, Shanon index. We used...

09 January 2014 5,498 7 View

Which material from carbon family can act as a potential counter electrode for DSSCs?

As i was searching for making a low cost CE for DSSCs fabrication.

01 January 1970 115 1 View

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Does Napabucasin soluble in dichloromethane and in ethanol?

I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...

02 March 2021 9,945 3 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Anyone found any research papers on solar furnace design calculations (for solar concentration)?

I am thinking about working on solar furnace with heliostats that concentrate sunlight and heat molten salt, but currently no luck with research. Not a lot of papers based on the subject. (check...

01 March 2021 5,023 5 View

Which fluorescent dye to use for measuring total ROS production?

Is DCFDA appropriate for measuring total ROS production, or can it only detect certain types of ROS? If I want to measure total ROS production, which dye should I use?

01 March 2021 9,447 3 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

Hassan Alshamsi

Please have a look at the below links and attached file.

https://link.springer.com/article/10.1007/s10008-011-1541-2

http://aip.scitation.org/doi/pdf/10.1063/1.4726177

http://ieeexplore.ieee.org/document/6357574/

http://iopscience.iop.org/article/10.1143/JJAP.51.10NE20/pdf

http://www.sciencedirect.com/science/article/pii/S0927775717301310

http://pubs.rsc.org/en/content/articlelanding/2011/jm/c1jm11145k/unauth#!divAbstract

http://agris.fao.org/agris-search/search.do?recordID=US201500096466

Muhammad Abbas

Yeah it is quite possible to drop cast the catalyst if it have some bonder (say, nafion etc) on the counter electrode, if it is Pt disk, for the wire, it would be very difficult to immobilize the catalyst.