Hello,
I want to model a parabolic hole in a slab using ABAQUS. Can i do it? if Yes how?
Hi Prashant
yes, it is possible.
1) in the part module select the slab,
2) in the left ribbon options, select the "cut extrude"
3) you will be gone back to the sketch part
4) draw your section
5) Done.
Best Lucks
hello sir,
thank you for the reply, i understand what you said, but even then i think you cannot create a circular parabolic duct at the center of slab.
Can you please draw a sketch? I am not able to get what exactly are you looking for.
SURE SIR
In the part module
1. Shape menu (at the top) > Cut > Sweep.
2. In the appeared menu,
(i) Sketch the path, i.e. parabola along the slab
(ii) Sketch profile, i.e. circle on the face normal to the path
You will be get it.
Exactly.
Plz follow the Mr. Faye instruction to approach your goal.
Dear Mr Faye and Mr Ghaedi.
Thank you for taking out time and replying
Yes its working this way but sir again how do i define the sweep at the center of slab. it is only possible to sweep cut on the faces this way.
Sweep path is independent of the sweeping geometry. You sketch the sweep path at the face and sweeping circle at the center of the slab. That should not be a problem.
Somewhere on the internet, it's reported the maximum diversity gain limit theoretically can be achieved is 10dB. Some papers said it increases with more antennae and some said it will decrease.
09 June 2024 5,121 2 View
any fully funded phd position in wildlife ?
25 May 2024 7,976 2 View
I am wondering if anyone has come across calibration curve and uncertainty for PM2.5, SO2, O3, and NO2 monitors maintained and operated by the CPCB? Please share link herein for the same if you...
25 April 2024 7,164 5 View
What are different ways of modelling and simulation of cascade refrigeration cycleusing natural refrigerants on MATLAB without using simscape ? How to write program for it and connect MATLAB...
02 April 2024 487 2 View
because people are citing/talking less about Classical texts discovered by Rishi/sages. Rishi has the broad scientific knowledge as per their practical and theoretical practices.
30 March 2024 2,013 0 View
How to evaluate the compounds with usage of peaks and their respective values in LCMS - TOF instrumentation? Is there any web portals for the data interpretation? I Have got Both LC (2 Files) MS...
13 March 2024 7,940 1 View
Alcohol consumption shift. Socio-econo-cultural factors, globalisation, westernisation, religious conversion role in alcohol consumption shift
12 September 2023 4,757 0 View
I have not understood here the method of design of fin and Fan for thermoelectric refrigeration system in paper attached .....................
09 August 2023 8,355 0 View
I have tried OES method to obtain composition of 2024 T4 multiple times. As per standard composition Cu should vary between 3.8-4.9 and Mg should vary between 1.2-1.9. The problem coming is that...
18 July 2023 450 0 View
In all research paper i found the Aluminium alloy D16AT and 2024T4 having same chemical composition . They are subjected to same heat treatment process. Are they different or same ???
16 July 2023 8,039 4 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.
07 August 2024 5,307 1 View