How fin and fan design is done for for thermoelectric refrigeration system ?

10 August 2023 0 8K Report

I have not understood here the method of design of fin and Fan for thermoelectric refrigeration system in paper attached .....................

Badges
Science topic

Similar topics
Correction

More Prashant Pathak's questions See All

How to do buckling analysis in ansys apdl for laminated plate with PZT 5H attached?

I am doing buckling analysis of laminated plate surface bounded with two piezoelectric PZT 5H and axial compressive load is applied. I am getting an error, No ANEL table exists for material 2....

16 February 2021 510 1 View

What is the method of removing RNase contamination from a filter paper surface?

I am working on a biosensing project on paper substrate, however, it is found that the RNase contamination occurs on the filter paper. Might I ask is there any method to clean the paper surface...

12 February 2021 3,926 3 View

What is causing the raw fluorescence to be negative?

Hi everyone, I would really appreciate it if someone can tell me when and why a raw fluorescence starts below zero. In the picture attached below the blue colour curve starts from a negative...

09 February 2021 4,642 3 View

Regarding immunology, transmissivity, herd immunity and vaccines in Sars CoV-2?

This is a follow-up on an earlier question regarding mechanistics of vaccines: why current vaccines don't block transmission. In summary, they don't engage mucosal immune cells to produce IgA....

08 February 2021 8,321 3 View

How can I enter the load increment values to the Abaqus?

In Abaqus I know that there are two methods for incrementation (Automatic and fixed incrementation). I want to control the incrementation by myself. I want to input the values of load increment...

03 February 2021 6,943 3 View

Distortion problem in Abaqus explicit?

Dear all. I'm modeling the RC column with cyclic displacement by Abaqus-Explicit. The concrete model used Concrete Plastic Damage model. However I'm facing with a error about the excessive...

01 February 2021 7,726 1 View

I am finding a lot of cellular debris in the culture flask? What are the reason behind it?

I am facing a problem that cellular debris observed in my SHSY5Y cells. I have seeded the cells in DMEM media with 10% FBS in T-25/ 60mm dish (antibiotic used PEN-Strepand gentamycin). I have also...

17 January 2021 3,074 3 View

What is the reason for discontinued Stage II fatigue crack growth in pearlitic steel?

Conventionally, the process of Stage II fatigue crack growth is governed by Paris law with less microstructural effect. When fatigue crack growth test was carried out for pearlitic steels ( both...

03 January 2021 7,075 3 View

Anyone have any knowledge about the authenticity of the European Journal of Humanities and Social Sciences - (EJ-SOCIAL)?

https://ej-social.org/index.php/ejsocial

30 December 2020 6,845 3 View

Which furnace or method are suitable for direct melting of the powder ?

My question is very specific about melting of pure reduced Iron Fe in powder form

29 December 2020 4,352 3 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

What are the main reasons to grow Escherichia coli O157:H7 and Salmonella Typhimurium in food products under refrigeration storage 4 C?

24 January 2021 9,987 3 View

I am trying to simulate phase change of refrigerant inside pipe extracting heat from panel in comsol. Can anyone help with how to simulate this?

My model is a rectangular multi layered structure under which refrigerant flows through cylindrical pipes. A heat flux of 600W/m2 applied on panel and internal forced convection is used for...

20 January 2021 9,478 1 View

Is it possible to calculate entalphy of LiBr/H2O or another solution if we know correlation of specific heat without using any software?

17 January 2021 5,522 3 View

How do i calculate the total heat transfer rate in COMSOL (5.4)?

I have modelled a condenser of a refrigerator in COMSOL. I made different designs and i want to calculate which design has the highest heat transfer rate. The way i calculate it now is by: q =...

02 December 2020 306 2 View

How can I determine the mass of a refrigerant (for example R744) in a evaporator when the refrigeration system is not working?

By knowing the specific volume on the inlet and on the outlet, is it correct to assume an average of those two specific volumes?

30 November 2020 3,807 3 View

Potassium formate/water or potassium formate+LiBr/Water are not available in the commercial sector for absorption refrigeration systems?

Although there are already studies in the literature but not much , the use of potassium formate/water or potassium formate+LiBr/Water are not available in the commercial sector for absorption...

16 November 2020 2,917 2 View

Is there any way to revive strains after a year stored in 4 degree refrigerator?

The strain is Candida tropicalis. It has been stored in 4 degree refrigerator for a year. Now we want to see if it is possible to revive the strain and make it function again. I tried to culture...

10 November 2020 5,650 9 View

No title

When producing a recombinant protein, harvested E. coli cells are normally refrigerated for 12-24 hours before homogenization to ensure protein inactivation due to foaming does not occur....

16 October 2020 7,373 0 View

How to calculate the dimensions and frequency, etc. of a pulse tube for required cold/hot temperatures?

Require to know the methodology for calculating dimensions (Lenght, diameter), operating frequency, etc. of a simple pulse tube refrigerator. Reference to handbook or manuscript would also be helpful.

29 September 2020 2,191 2 View