Is it possible to exfoliate Metal Ferrites with solvent exfoliation method?

More Mayuri Bora's questions See All

What will be the synthesis process to get Manganese based alloyed quantum dot system?

What can be the synthesis process of Mn based alloyed quantum dots? Will it be same kind of process followed by ZnSe(S) alloyed quantum dots?

07 August 2017 2,995 3 View

Why Mn based alloyed quantum dots does not show fluorescence even after 13 hrs of reflux?

I did not understand why Mn based alloyed quantum dot is not showing fluorescence even after refluxing for 13 hrs. Should I reflux for more hrs or should i change the compound of the Mn precursor...

07 August 2017 5,505 0 View

What is the solvent for 8YSZ nano material?

I need to do some experiment with it in liquid form.

07 August 2024 613 3 View

Which solvent is better to dissolve with secondary metabolites extracted from fungi?

I work on MCF7 cell cell for anticaner purpose and I wa to do drug preperation the drug ( secondary metabolites extracted from Aspergillus) My question which solvent is better with these secodary...

03 August 2024 4,725 2 View

I need to dissolve stigmasterol for an animal experiment, it hasn't dissolved in either DMSO or vegetable oil. Can anyone recommend the best solvent?

Hello everyone, I need to dissolve stigmasterol for an animal experiment, but it hasn't dissolved in either DMSO or vegetable oil. Can anyone recommend the best solvent for stigmasterol?

01 August 2024 7,504 2 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

Why methanol and sulphuric acid used in the analysis of polyhydroxyalkanoates (PHA) by GC-MS?

Why methanol and sulphuric acid, used in the analysis of polyhydroxyalkanoates (PHA) methyl esters by GC-MS? Additionally, why do we typically use non-polar solvents in GC-MS?

22 July 2024 1,210 2 View

When making abraxane with Nab tech, why is 9:1 Chloroform&EtOH used as solvents?

Is it the best optimization ratio based on experiments?

22 July 2024 8,170 0 View

What is the solvent system required to run tlc for calixarenes?

If you don't understand my question let me know

21 July 2024 563 1 View

Convergence of absorbency values to determine the total phenolic content of several solvents?

I used several solvents and measured the absorbency and determined the total phenolic content, but the results were similar after dropping them on the titration curve; What is the reason, please help

17 July 2024 5,151 5 View

How Can I Resolve a Persistent Unwanted NMR Peak at 1.25 ppm?

Hello everyone, I am facing a consistent issue in my NMR spectra with an unwanted peak appearing at 1.25 ppm. This peak seems to vary with the amount of sample: it becomes more pronounced with...

15 July 2024 9,065 4 View

What is the suitable solvent of MIL-100 for chemotherapy?

I synthesised a nanocarrier by conjugation MOF (MIL-100) with folic acid for use in chemotherapy but the samples didn't dissolve completely in aqueous solution or DMSO. Instead, they only...

15 July 2024 2,414 1 View

Imad Disher

Exfoliation is possible for some materials that has layered structure such as graphite and some clay minerals. Ferrites haven't such structure.

Mohammad Kooti

I suggest you use sonication to disperse the metal ferrite in solution. Ferrites are magnetic and tend to aggregate in solution.

Mayuri Bora

Dear Mohammad kooti,

Even i was thinking of sonication after the preparation of the material in bulk. Thank you for your suggestions.

Yes, try sonication of the bulk material for longer time and check the size of NPs obtained.