Why Mn based alloyed quantum dots does not show fluorescence even after 13 hrs of reflux?

08 August 2017 0 5K Report

I did not understand why Mn based alloyed quantum dot is not showing fluorescence even after refluxing for 13 hrs. Should I reflux for more hrs or should i change the compound of the Mn precursor where i am using MnCl2.4H20 as the Mn precursor.

https://www.researchgate.net/profile/Alexander_Titov2

https://www.researchgate.net/profile/Tanuj_Trivedi

Badges
Science topic

More Mayuri Bora's questions See All

Is it possible to exfoliate Metal Ferrites with solvent exfoliation method?

Even if we synthesize metal ferrites as a bulk then is it possible to exfoliate the synthesized metal ferrites with any solvent exfoliation technique.

06 July 2018 9,417 4 View

What will be the synthesis process to get Manganese based alloyed quantum dot system?

What can be the synthesis process of Mn based alloyed quantum dots? Will it be same kind of process followed by ZnSe(S) alloyed quantum dots?

07 August 2017 2,754 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

How to accurately quantify chitin?

Hi all, I have been working on the quantification of chitin in insect samples and feed for a while but I can notice that the quantification methods (e.g. exposure to HCl, NaOH, and weighing sample...

01 March 2021 1,843 2 View

Can someone suggest a way to prepare slides to observe under confocal microscope for observing fluorescent tagged proteins??

I am growing the cells on coverslips and transfecting the fluorescent tagged protein directly on them. Then i want to observe these cells under confocal microscope. Currently i am just using...

01 March 2021 6,142 3 View

Why does intensity drops as concentration increases?

Is there any reason for decrease in fluorescence emission intensity of HSA,BSA when increase the concentration ?

28 February 2021 3,653 4 View

Quantifying leaking DNA from bacteria - what's the secret?

Hi, all! I need to determine if my treatment causes membrane damage in bacteria (S. aureus and E. cloacae), but I cannot use a fluorescent probe such as PI and similar ones because my compound is...

24 February 2021 2,006 2 View

How to determine solutionizing time for cast Al alloys?

For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys

23 February 2021 8,839 3 View

Which thermal conductivity test recommended for Ag-Cu nanofluid?

I have prepared Ag-Cu alloy with polymer coating upon it.... how can I measure thermal conductivity of it ?

22 February 2021 5,915 3 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View