Is it possible to check the strength of weld joint using ANSYS?

Raja Varadharaj @Raja_Varadharaj

02 February 2017 1 855 Report

if joint strength is measurable using ansys, we can use the principle for Bi-metallic castings also.

Sathish Dhandapani

https://eprints.usq.edu.au/29295/1/Mohammed_R_Snook.pdf

Badges
Science topic

More Raja Varadharaj's questions See All

How to model a bimetallic pipe using finite element analysis?

How to model a bimetallic pipe using finite element analysis? If material 1 is cast first and material 2 is cast over to the material 1.

31 December 2019 1,640 5 View

How to make interaction plot for L9 OA?

show me the linear graph to make interaction plot for L9 OA.

04 May 2017 4,745 0 View

How to get pure bainitic micro structure in iron carbon phase?

what will be the advantage of getting bainite over martensite.

01 February 2017 4,425 0 View

How long the particle boards will survive in moisture environment?

effect of moisture on particle boards control the natural hindrance to the boards

01 February 2017 7,168 3 View

How to take time study at institution level?

can you suggest some methods to conduct time study in an engineering college?

01 February 2017 7,211 0 View

Discuss push out test procedure for a bimetallic casting?

I want to know the standard testing methodology for push out test. Where I can use this facility in India? I want to know the institution name. Thank you.

01 February 2017 831 0 View

How to identify properties of work material by evaluating chips obsevation ?

when turning a work material in lathe, the properties of material can be measured by identifying the chip flow.

01 February 2017 1,993 10 View

What is Hess Law?

need to use hess law in thermodynamics.

31 December 2016 7,274 7 View

Can we integrate stir casting technique on squeeze casting machine?

Hi dears, how to integrate stir casting and squeeze casting.

01 January 1970 531 2 View

How can i determine the intermediate temperature between hot liquid and cold metal?

When the molten metal solidifies, how the temperature will be distributed to solid cold metal? I need to know the mathematical modelling of such compound casting.

01 January 1970 5,662 8 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

What may be the reasons for failures of Tube toi Tube Sheet Joints in Boiler Drum ?

We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.

08 August 2024 3,161 0 View

London dispersion in CCl4 vs the dipole-dipoles force strength in CHCl3?

How do you tie-break and rank these two in their strength?

03 August 2024 4,471 1 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View

I ask Chinese seismologists to inform me: who should I contact to create a joint Forecast Center?

I ask Chinese seismologists to inform me: who should I contact to create a joint Forecast Center? I do not hide that the beginning of my work was connected with the successful forecast of the...

22 July 2024 2,276 1 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View