Is it possible to add Japanese codes to Etabs or SAP2000?

More Manoj Pradhan's questions See All

In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

Can anyone provide the Support vector regression code structure of LIBSVM MATLAB or python ?

Please, if Gaussian Parameter optimization is possible in this code structure

28 February 2021 278 3 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

Selection of Steel Frame Section in SAP2000?

Hello, I have a technical question about the selection of steel frame sections in the designing of steel frame structure i.e W16x48 etc. The common practice I have seen is the trial and error...

11 November 2020 5,762 4 View

Can anyone please tell how to define link for Tuned mass Dampers using Sap2000/Etabs?

Dear Research scholars, I was doing my MTech thesis on pendulum based TMD and I was having trouble defining the link properties. I even followed the tutorials put on CSI website. still, I wasn't...

11 November 2020 8,309 11 View

Can i apply bell method to equilize the histogram in ImageJ, please let me know the way if that can be done ?

This question is regarding the use of imageJ, I want to apply the same effect to my image that can be done by the command "ret = IpHstEqualize(EQ_BELL)" in image pro premier. I have imageJ only...

01 November 2020 5,660 1 View

Stiffness changes of the structures due to modeling P-Delta effects in Sap2000 are more significant than OpenSees. which is more accurate?

Dear researchers The modeling of P-Delta for the structural elements (specially columns) reduce the stiffness of the structure and consequently increase the period of vibration. Now, these...

24 October 2020 7,255 5 View

[SAP2000 related] I wonder why there is no any effect in the analysis result when I change the different parameters while modeling a frame structure?

(i) I have modeled a simple 2D frame structure (2 columns and 1 beam). I would like to see the variation in the result by varying the different parameters such as, sizes of confinement bars,...

06 October 2020 9,496 5 View

How can material nonlinearity be modelled in SAP2000?

Can we model nonlinear behavior of area elements for in-plane stresses?

17 August 2020 9,800 5 View

Moment curvature plot in SAP2000: What should i refer to understand the background calculation which SAP2000 does to generate the M-phi ?

The moment-curvature plot in SAP2000 is based on the material stress-strain plot of caltran (along with its material FoS). I would like to understand the detailed calculation to obtain the plot...

13 August 2020 5,729 3 View

Which is your preference when analyzing 3D frames; STAAD, ETABS, LUSAS, RISA 3D SAP200 or ROBOT?

In a followup question to what was previously asked, which of the following would you recommend for analysis and performing design checks on 3D frames: (1) STAAD (2) ETABS (3) SAP2000 (4)...

02 August 2020 3,717 11 View

How staad pro analyze Response spectra problem?

I am modelling a steel structure problem in STAAD Pro. I want to check behaviour of that steel structure against Response Spectrum. I have facing challenges in understanding of how STAAD Pro...

08 July 2020 1,093 1 View

How to add plate above the beam in STAAD Pro?

I have facing problem in analyzing a steel structure that has steel plates above and below the steel beam. Is there any way to add plates? I have added plates at center but that decreases moment...

08 July 2020 1,697 1 View

Usama A Ebead

I believe that there is a list of design codes supported by SAP. You may want to ask the software providers so that they can include the Japanese codes in a next software release or update.

Manoj Pradhan

Prof. Ebead, thank you for the reply. It seems there's no other option than to wait for future releases.

Vitalie Florea

It is not possible manually.

This is the supported codec list:

https://www.csiamerica.com/international-design

Hussam Ali Mohammed

Good question.. Please share me the best answer might you trust...

Regards…