Is it possible for an E. coli cell to have different morphology during growth?

More Shridhar Kinkar's questions See All

Which softwares are useful in graph theory and in particular in spectral graph theory?

Path Eigenvalues and Path Energy of Graphs

19 September 2020 8,258 7 View

Is it possible that FWHM is same for all the XRD peaks of a particular material?

Hello, I am doing XRD data analysis of a certain material which may have more than one phases. While calculating crytallite size I noticed that almost all peaks have same FWHM except 3 peaks. Can...

03 February 2020 7,303 1 View

Where do we get characterization of nano materials like XRD,SEM,FTIR and dielectrical and magnetic studies as early as possible?

Where do we get characterization of nano materials like XRD,SEM,FTIR and dielectrical and magnetic studies as early as possible? Please help us.

20 December 2019 1,516 3 View

What is the minimum time required for a standard ligation reaction using T4 DNA ligase at 1U/ul concentration?

Hello everyone, I have a vector backbone of 5.5Kb in which I need to ligate an insert of ~600bp. The Roche T4 DNA ligase manual I'm using says ligation should be kept for 16h @ 16 deg. Celsius. My...

17 December 2019 4,523 8 View

How do you write a good review paper?

What is a scientific review article? How do you write a review article format? How do you write a scientific journal article? How do you write a good review paper? How do you write an introduction...

15 March 2019 424 5 View

Which are the new novel Solar cell materials?

Which are the new novel Solar cell materials? We are new to this field. I have to synthesis these materials through PVD process.

13 November 2018 7,389 4 View

How to write a better research projects? Kindly share some samples in material sciences?

Dear Sir/Madam How to write a better research projects? Kindly share some samples in material sciences? I am working in the field of ferrites and ferroelectrics. KIndly share some documents or...

17 October 2018 8,848 3 View

Need to know if higher IPTG concentrations make E. coli expression host undergo a metabolic stress?

Hi, I have been titrating best IPTG dose for highest expression of my GOI. However, I found that after a certain concentration (2.5mM), post-induction OD600 of culture shows lesser growth and as a...

28 January 2018 1,522 3 View

What is the best way to purify tagless and soluble TNFa?

I expressed TNFa in E. coli BL21 (DE3) host and got satisfactory expression. The protein is tagless. My question is how do I purify it? Which chromatography techniques can I use and what should be...

22 September 2014 918 17 View

Electrolytes in Supercapacitors

Hi, Can anyone help me, I want know, which materials can we use as electrolytes in Supercapacitors other than Potassium hydroxide and Sulfuric acid. For better power density or energy density.

05 October 2010 8,863 3 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

How to normalise data on OPM package from R Studio ?

Good afternoon, I recently used OmniLog from BIOLOG for my experimentations : I tested the metabolism of different strains on 2 types of plates. I have 16 strains of 3 different groups...

02 March 2021 3,584 1 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

What is the most suitable server for predicting protein structures in bacteria?

I have used the i-Tasser several times, however it has been unavailable for several days. I tried the swiss-model, but the output was not very pleasant due to the model used. Is there any other...

28 February 2021 4,521 3 View

SEM or Multiple Regression for an analysis without Latent Variables?

Hello, I have three hypothesis to test, all with the same IV. I am testing if the effect of the IV on the first DV is mediated by awe. I am then measuring whether the effect of the IV on a...

26 February 2021 8,399 5 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

Has anyone used the Illumina ITS1 primer sets?

Hi everyone, Illumina provides a list of primers to amplify with high taxonomic coverage the ITS1 region for further fungal sequencing, but I cannot find the exact amount necessary of each...

25 February 2021 6,969 3 View

Alireza Mordadi

Your answer is completely positive not possible.

Take article below.

https://academic.oup.com/femsec/article/83/3/622/595323

Study each model and keep digging.

You will find your answer.

Regards

Shridhar Kinkar

Hello all,

Thanks for your help... I have got biochemical tests done and it says it is E. coli. That's what has created the confusion.

Huan Gu

It depends on the stage the condition of your culture. Escherichia coli is long in exponential phase. When it attaches onto a soft surface, it is more prone to become longer.

Traci L Testerman Thank you very much for such an explanatory answer. This will certainly help me in my quest... :-)