Influences of the temperature on vonmises stress and principal stress in laser melting of Titanium alloys?

Mallikarjuna Balichakra @Mallikarjuna_Balichakra2

08 August 2017 1 8K Report

Hi everyone

I have done the simulation of laser remelting process on titanium alloys. I want to know how does the temperature effects the vonmises stress and principal stress. Also, please do suggest me is there any related journal papers.

Joseph Ahn

Temp can cause solid state phase transformation. It will then affect the phase ratio and phase dependent mechanical properties for example.

Badges
Science topic

More Mallikarjuna Balichakra's questions See All

What are the true stress- true strain curves at different temperature for Ti-48Al-2Cr-2Nb alloy?

Hi everyone Can anyone please share the stress-strain curves for TiAl based Ti-48AL2Cr-2Nb alloy for thermomechanical analysis in ANSYS.

31 December 2017 8,574 0 View

What are the Grain size of Alpha and Beta phases at 750oC in Titanium aluminide (Ti48Al2Cr2Nb) alloy ?

Hi everyone Can anyone help me out on above question. At 750 c it has alpha and beta phases. So in-order to calculate flow stress following are required1.alpha grain size:2.beta grain size :

08 September 2017 6,395 0 View

Can any one suggest me the material modeling in ansys APDL?

Specifically explain about Bi-linear and multi-linear and what are the properties are must to do this simulation. These are dependent on which models

01 February 2017 5,970 0 View

Element birth and Death technique

Can you anyone help me regarding element birth and death technique. My questions 1) what is the value of Stiffness multiplication for transient thermal analysis in element birth and death...

04 May 2016 6,821 4 View

How do I couple the transient thermal analysis with structural analysis in ansys for finding the thermal stresses?

1) How to couple the transient thermal analysis into the mechanical analysis(structural analysis) to find the residual stresses 2) In ansys software 3) I have the transient thermal simulation...

11 December 2015 9,298 4 View

What is the absorptivity (alpha value) of Ti-48Al-2Cr-2Nb alloy for this material??

This is an intermetallic alloy, is there any formula to find out the alpha(Absorption) value for this material.

09 October 2015 8,356 2 View

What are the properties of Nitinol materials such as temperature wrt conductivity, specific heat and density?

For example Temperature(c) conductivity(w/m k) Specific heat Density(kg/m3) 25 6.5 60 4470

03 April 2015 3,084 5 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Are authors sowing for scientific Journals to be reaping the benefits? We are charged for publication but we offer free peer review services, why?

As authors and academic writers, we usually prepare our manuscript using our own resources. We submit these manuscripts to scientific Journals for peer review and publication sometimes at a fee....

03 August 2024 7,304 2 View

What is the role of oxidative stress in toxin-induced carcinogenesis?

What is the role of oxidative stress in toxin-induced carcinogenesis? I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from...

02 August 2024 3,174 1 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Could GSH level be more in CCL4 rats than negative control rats?

i compare between the antioxidant and oxidative stress level between negative control rats (saline) and CCL4 intoxicated rats. i found the level of GSH and TAC is more in toxic group than normal....

26 July 2024 1,887 0 View