In ANSYS Fluent, adding a line in XY plot by getting its average value can be considered as bulk fluid temperature?

Wei Xian Hong @Wei_Xian_Hong

12 December 2016 1 8K Report

ANSYS

supercritical methane in pipe

bulk fluid temperature in XY plot

Wei Xian Hong

currently running simulation on this paper:

Article Experimental investigation on convective heat transfer from ...

Badges
Science topic

More Wei Xian Hong's questions See All

I was acknowledged that true density must be used to compute required amount of nanopowders. How if only bulk density is available from supplier?

Functionalized graphene nanoplatelets

08 September 2018 2,563 3 View

Does ball mill only rely on its RPM for grinding ? How about friction inside the jar?

ball mill, stainless steel media, friction

04 May 2016 2,431 1 View

If diameter of ball mill jar(not planetary type) is too small, is it still able to grind metal pieces into powder? Or just increase RPM will do?

ball mill small RPM

03 April 2016 7,593 3 View

How can I determine the best RPM for Dry Ball Milling machine in order to let the balls to fall from the best angle(s) ?

1. Designing 40cm cylinder 2. Going to grind ceramics.

02 March 2016 4,466 7 View

Will the heat generated in gear tooth transferred to the center of gear and escape through convection?Heat generated will affect efficiency of system?

1. gearing system 2. heat transfer through convection from side surfaces 3. friction between gear tooth 4. how to reduce heat generated instead of using lubricant

01 February 2016 4,232 2 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View